IBC VFC 15-150 Скачать руководство пользователя

Страница: 19 / 80

1-13

INSTALLATION

VFC 15-150, VFC 45-225 MODULATING GAS BOILERS

Air intake filter IBC Part #SC100A

1.4.9 Combustion Air Filtration

If combustion air contamination from ingested particulate matter may be a

concern in any installation, an optional air intake filter may be installed. IBC

supplied air intake filters have a known pressure drop and fouling factor and

should be used as a component of the combustion air system according to the

allowable intake length in

Table 4.

1.4.10 Closet Installations

For installations in a confined space (such as a closet), ventilation openings may

be needed through a door or wall to prevent excessive heat from building up

inside the space.
The boiler shall not be exposed to ambient conditions above 122°F (50°C) or

below 32°F (0°C).

NOTE

Combustion fan

blockages can occur when

environmental particulate and

foreign matter contaminants

(leaves, dust, dandelion &

cottonwood fluff, etc) are

drawn into the air intake. In

areas where this problem is

suspected to be an issue,

our optional air intake filter

should be installed.
Filters should be checked

and cleaned or replaced on

a regular schedule based on

the severity of the problem.

Figure 13: Direct vent - intake, exhaust and condensate removal system with optional air

intake filter (filtration may also be used on indoor air applications as required)

Figure 12: Optional air intake filter

IBC Part #SC100A - Filter element

alone is IBC Part #180-103

Содержание VFC 15-150

















































































Результаты поиска

Содержание VFC 15-150

Отзывы:

Похожие инструкции для VFC 15-150

Бренды по названию

Популярные бренды

IBC VFC 15-150, Инструкция по установке и эксплуатации

Результаты поиска

Содержание VFC 15-150

Отзывы:

Похожие инструкции для VFC 15-150

Бренды по названию

Популярные бренды