background image

SAS0715

Page 

4

LOCATION  &  INSTALLATION

1.

The  softener  requires  an  inlet  water  pressure  between  140kPa  (20psi)  and  690kPa
(100psi).

2. 

The softener should service all water lines in the house except the toilet and outside taps.
The  softener  should  be  positioned  on  a  level  flat  surface  close  to  a  drain  or  any  other
properly trapped waste outlet.

The brass adaptors supplied are suitable for 20mm (3/4") female fittings and the softener
should  be  connected  to  the  supply  with  raw  water  to  the  inlet  connector  and  softened
water lines to the outlet as indicated on the valve.

3. 

When facing the front of the control the inlet is to the right and the outlet is to the left.

4. 

The system pressure must be between 140 kPa and 690 kPa psi.

5. 

If the system pressure is greater than 690kPa psi a 

pressure  reducing  valve

  must  be

installed.

6. 

The unit must be installed in accordance with local codes.

7. 

Do not over tighten connections.

8. 

Drain line ID must be at least 12mm.

9. 

Teflon tape should be used when installing he drain fitting into the control valve.

10. 

The drain line must be free of kinks.

11. 

A safety float with an air check is installed.

12. 

Insure all connections are tight.

13. 

To initiate regeneration, turn the twist the timer knob clockwise to the 2 hour position.

Note:  DO NOT use teflon tape when connecting the fitting kits to the control valve.

14.

There are two drain lines, one from the brine tank and one from the softener valve, these
lines  must  have  an  air  gap  of  at  least  40mm  or  twice  the  pipe  diameter  at  the  drain
entrance. The drain line from the brine tank is gravity fed and hence the drain is required
to be below the outlet elbow on the tank.

The  drain  line  from  the  softener  valve  is  under  pressure  during  regeneration  but  for
correct operation a maximum of 2.4m of 15NB pipe with no rises can be connected.

A manual Bypass should be installed.

Содержание SAS0715















Отзывы: