manualshive.com logo in svg

IBC Technologies VFC 15-150, Инструкция по установке и эксплуатации

Поделиться
Скачать
IBC Technologies VFC 15-150 Скачать руководство пользователя страница 43

IBC Technologies Inc. 

43 

VFC 15-150 and VFC 45-225 

to the right of the heat exchanger. Disconnect the Molex connectors located approx. 6” from 
the sensors. Place multi-meter probes into Molex socket.  Do not apply voltage to the sensor 
as damage may result. 

Sensors are sensitive to excess binding force, which can distort the internal dielectric 
isolation. Use modest tension only when affixing sensor to pipe. 
 

Temperature 

Resistance Temperature  Resistance Temperature  Resistance Temperature  Resistance 

°F °C 

Ω

 

°F

 

°C

 

Ω

 

°F

 

°C

 

Ω

 

°F

 

°C

 

Ω

 

0 -18 85,362 50 10 19,900 100 38  5,828 150 66  2,045 
5 -15 72,918 55 13 17,436 105 41  5,210 155 68  1,857 

10 -12  62,465 60 16 15,311 110 43  4,665 160 71  1,689 
15 -9  53,658 65 18 13,474 115 46  4,184 165 74  1,538 
20 -7  42,218 70 21 11,883 120 49  3,760 170 77  1,403 
25 -4  39,913 75 24 10,501 125 52  3,383 175 79  1,281 
30 -1  34,558 80 27  9,299 130 54  3,050 180 82  1,172 
35 2  29,996 85 29  8,250 135 57  2,754 185 85  1,073 
40 4  26,099 90 32  7,334 140 60  2,490 190 88  983 
45 7  22,763 95 35  6,532 145 63  2,255 195 91  903 

4.3.2.2

 

Fan/Blower 

Operating power is provided by means of a separate 120 V

AC

 connector at the back of the fan 

(white/black/green). Control of the fan is provided via a four lead connector at the front of the 
fan. This connector feeds a PWM control signal (black wire) from the controller and provides 
a tachometer signal (white wire) back from the fan. Unplugging the connector will cause the 
fan to go to high speed and trigger a “Blocked Vent Error” within 6 seconds if the boiler is 
operating.  
 

Table 6 - Fan Operation 

Lead Color 

Function 

Troubleshooting 

Red 

35Vdc. Positive power 
terminal 

Fan will only operate at max. 
speed if disconnected. 

Blue 

35Vdc. Negative power 
terminal 

Fan will only operate at max. 
speed if disconnected. 

Black 

Signal from controller 

Fan will only operate at max. 
speed if disconnected. 

White 

Fan tach. 

2 pulses /rev (freq x 30=rpm. 

4.3.2.3

 

Differential Air Pressure Sensor 

Go to the 

Advanced Diagnostics

 screen, and with the fan off (“

Fan Duty Cycle

 = 0) look for a 

Fan Pressure

 reading of 102 +/-5. Next check with fan in operation, and look for an increased 

Fan Pressure

 value. In normal operation, the 

Fan Pressure

 reading should move toward the 

Required Pressure

 value. A backward movement in 

Fan Pressure

 indicates the clear vinyl 

reference lines have been reversed.  

Next, confirm that the circuit is properly powered. The supply voltage to the sensor should be 
13.8 V

DC

; to check, the simplest technique is to measure the circuit on the face of the 

controller circuit board (vs. an attempt to splice into the harness / connectors). See below for a 
presentation of the measurement points. 

Содержание VFC 15-150


























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды