IBC Technologies SL 30-175 страница 46 Скачать руководство пользователя

Страница: 46 / 78

INSTALLATION AND OPERATION INSTRUCTIONS

3-4

SL 30-175, SL 45-260 MODULATING GAS BOILERS

Fuel ConVersion

The SL 30-175 and SL 45-260 modulating boilers are factory fire-tested to

operate with natural gas, or propane as ordered. the rating plate will be marked

to indicate which fuel the particular boiler has been set up with. Firing a boiler

with a fuel other than what is listed on the rating plate is prohibited unless the

following conversion procedure is completed by a qualified technician.
refer to the preceeding section 3.3 - CoMMissioning. the Zero-offset valve

adjustment cap on the gas valve has been factory sealed using red paint-seal

compound.

This cap must not be tampered with. The Zero-offset screw is

not to be adjusted in the field.

the gas:air ratio adjustment screw will have to be adjusted to attain optimum

combustion results whenever fuel conversion is undertaken, however,

mixture adjustment shall be performed unless done by a qualified

technician using properly functioning and calibrated combustion analyzing

equipment.

The following procedure can be carried out by a qualified technician

(see Figure

33).

ensure that the gas supply is turned off at the gas control valve.

loosen the gas valve harness plug screw and disconnect the gas valve

harness plug from the gas valve.

disconnect combustion air snorkel from the venturi.

uning a 4 mm hex head wrench, undo the three venturi mounting screws.

separate and lift the gas valve up and away from the venturi assembly.

If converting a Natural Gas boiler to Propane

: remove the brass Propane

orifice from its packaging and seat the orifice inside the rubber grommet in

the gas valve body.

If converting a Propane boiler to Natural Gas:

remove the brass Propane

orifice from the inside of the rubber grommet in the gas valve body.

Do not

disturb the rubber grommet.

re assemble the valve to the venturi assembly and tighten the three venturi

mounting screws.

restore gas supply by opening the gas control valve, and using an approved

leak detection solution, soap test all joints.

Place the conversion labels associated with the new fuel onto the boiler at

the positions indicated on the the applicable conversion Kit instruction sheet.

•

For the sl 30-175 natural gas to Propane conversion Kit - iBC Part #168a

•

For the sl 30-175 Propane to natural gas conversion Kit - iBC Part #169a

•

For the sl 45-260 natural gas to Propane conversion Kit - iBC Part #170a

•

For the sl 45-260 Propane to natural gas conversion Kit - iBC Part #171a

10.

Carefully follow the “Prior to start-up “ - section 3.2 and “Commissioning” -

section 3.3 procedures on the preceeding pages 3-2 and 3-3.

3.4

DANGER

Operating any IBC boiler

using a fuel other than the

fuel listed on its rating plate is

prohibited. If the information

in this section related to

conversion to alternate

fuels is not followed exactly,

a dangerous situation can

result, leading to fire or

explosion, which may cause

property damage, personal

injury, or loss of life.

Disconnect gas valve harness plug

Disconnect combustion air snorkle

Содержание SL 30-175















































































Результаты поиска

Содержание SL 30-175

Отзывы:

Похожие инструкции для SL 30-175

Бренды по названию

Популярные бренды

IBC Technologies SL 30-175, Инструкция по установке и эксплуатации

Результаты поиска

Содержание SL 30-175

Отзывы:

Похожие инструкции для SL 30-175

Бренды по названию

Популярные бренды