IAI SW-4000M-PMCL страница 38 Скачать руководство пользователя

Страница: 38 / 43

SW-4000M-PMCL

Power supply voltage

DC input range: +12 V to 24 V ±10%
5.22 W typical (current consumption at DC +12 V supply)

Lens mount

M42 mount, F mount

Flange back

M42 mount: 16 mm (in air), tolerance: 0 mm to –0.05 mm
F mount: 46.5 mm, tolerance: 0 mm to –0.05 mm

Optical axis accuracy

Center ±0.5 mm (Max)

Operating temperature /
humidity

-5°C to +45°C / 20% to 80% (non-condensing)

Storage temperature /
humidity

-25°C to +60°C / 20% to 80% (non-condensing)

Vibration resistance

10G (20 Hz to 200 Hz XYZ directions)

Impact resistance

80G

Standard compliance

CE (EN61000-6-2, EN61000-6-3)
RoHS/WEEE
FCC Part15 Class B

Dimensions

62 x 62 x 84 mm (WHD) (F mount, excluding protrusions)
62 x 62 x 53.5 mm (WHD) (M42 mount, excluding protrusions)

Weight

320 g

Connectors / LEDs

Mini Camera Link
(SDR Type)

Model: HDR-EC26FYTG2-SLT × 2
Function: video output / communication / external trigger /

EEN

Positive polarity for EEN (polarity switching not possible)

12-pin

Model: HR10A-10R-12PB (71)
Function: power supply input / communication / external

trigger / EEN

Negative polarity for EEN (polarity switching not
possible)

Rear panel LED

Model: SPR-39MVWF
Function: operation display / trigger input display

In this document, the “X” in the XEEN represents the negative polarity.

Package contents

Camera body (1)
Sensor protection cap (1)
Dear Customer (sheet) (1)

Design and specifications are subject to change without notice.

— 38 —

Содержание SW-4000M-PMCL












































Результаты поиска

Содержание SW-4000M-PMCL

Отзывы:

Похожие инструкции для SW-4000M-PMCL

Бренды по названию

Популярные бренды

IAI SW-4000M-PMCL, Руководство пользователя

Результаты поиска

Содержание SW-4000M-PMCL

Отзывы:

Похожие инструкции для SW-4000M-PMCL

Бренды по названию

Популярные бренды