IAC INDUSTRIES Workmaster Storage Cabinet Series Скачать руководство пользователя страница 2

 

Table Of Contents 

 
Page # 

 

 

 Pre-assembly Check List 

3-4 

 

 WSC Worksurface Cabinet/Storage Mounting 

5-6 

 

 WSC Worksurface Support Beam Assembly 

7-8 

 

 WSC Leg Assembly 

9-10   

 WSC Lower Metal Shelf Cabinet to Pedestal Assembly 

11 

 WSC Lower Metal Shelf Cabinet to Cabinet Assembly 

12 

 WSC Shelf 

13 

  

 ESD Grounding 

 

ATTENTION NOTES:

 

 

IAC Industries takes great care in the packing of it’s products, however damage 
can occur during shipment. Check all packages and parts for any signs of 
damage. If damage is evident STOP and contact the carrier that delivered your 
order. Request a freight claim inspector to document the damage and begin the 
freight claim process. 
 
Tools required to assemble your products are: 
 
7/16” and 1/2” wrench or socket with ratchet.  
Ph

illips screw driver 8” long. 

Utility knife. 
Safety glasses and light duty protective gloves. 
 
Power tools are NOT recommended unless they are equipped with a torque 
limiting device which can limit the torque to 10 foot lbs maximum. 
 
Unpack your order and separate like parts. Be careful not to damage parts as they 
are being moved into position. Also be sure all parts are removed from the 
packing materials before these materials are thrown away. 
 
Locate the hardware kits and keep them in a central area. If the assembly is going 
to take more than one day, all individual hardware pieces should be returned to a 
central location. 
 
Check all parts and hardware kits against the itemized packing list found with the 
assembly instructions. If you believe there are parts missing from your order 
please contact IAC Industries customer service at 800-989-1422. 

 

 

WARNING

:

 

 

ALL PARTICLE BOARD USED IN IAC INDUSTRIES PRODUCTS ARE SOURCED ONLY FROM 
VENDORS THAT ARE CARB ATCM PHASE 2 AND TSCA TITLE VI COMPLIANT WITH VALID 

CERTIFICATES

.

 

Drilling, Sawing, Sanding or Machining Wood products can expose you to wood dust, a substance 

known to the state of California to cause cancer. Avoid inhaling dust generated from wood products or use a dust mask to 
other safeguards for personal protection. This product can expose you to chemicals, including formaldehyde, which is 
known to the state of California to cause cancer, and methanol, which is known to the state of California to cause birth 
defects or other reproductive harm. For more information please visit

www.P65WARNINGS.CA.GOV/WOOD

COPY OF 

VENDOR CERTIFICATE AVAILABLE UPON REQUEST. 

Содержание Workmaster Storage Cabinet Series














Отзывы: