background image

2

i3-TRNG-CAMS-

Di721/Do721

.indd

Rev. 

130130

Di721/Do721-series Camera Quick Start Guide

COPYRIGHT 

©

  2012 by i³ International, Inc. All rights reserved.

No part of this manual may be reproduced or transmitted in any form or by any 
means, electronic or mechanical, including but not limited to, photocopying, 
recording, or by any information storage or retrieval system, without the prior 
written permission of the copyright owner and the publisher.
Di721/Do721-series is a registered trademark of i³ International Inc.

Disclaimer

This 

quick start guide is provided as is, without warranty of any kind, expressed or 

implied, including but not limited to performance, merchantability, or fitness for any 
particular purpose. Neither i³ International Inc. nor its dealers or distributors shall be 
liable to any person or entity with respect to any liability, loss, or damage, caused or 
alleged to have been caused directly or indirectly by this information.
Furthermore, i³ International Inc. reserves the right to revise this publication, and to 
make changes to the content at any time, without notice.

FCC

This device complies with part 15 of the FCC Rules. Operation is subject to the 
following two conditions: (1) This device may not cause harmful interference, and (2) 
this device must accept any interference received, including interference that may 
cause undesired operation.

Address:

i³ International Inc. 
780 Birchmount Road, Unit 16 
Scarborough, ON M1K 5H4 
Canada

Contact us:

Tech Support: 1.877.877.7241
Email. [email protected]  
Web Site: www.i3international.com

Table of Contents

1.  Warnings and operation notes
2. Unpacking
3. Installation
4. Configuration
5.  OSD Settings
6. Specifications

Содержание Do721 Series























Отзывы: