background image

 

MACHINE SPECIFIC SAFETY

 

phenomenon) or carpal tunnel syndrome. This condition reduces the ability of the 
hand to feel and regulate temperature, causing numbness and heat sensations and 
may cause never damage and circulatory tissue death. 

1.62 

Not all factors that lead to white finger disease are known, but cold weather, smoking 
and other diseases that affect blood vessels and blood circulation as well as large 
and long-lasting impact of shocks are considered factors in the formation of white 
finger. Note the following to reduce the risk of white finger and carpal tunnel 
syndrome; 

1.63 

Wear gloves and keep your hands warm. 

1.64 

Take regular breaks. 

1.65 

All of the above precautions may help reduce the risk of white finger disease but not 
rule out the carpal tunnel syndrome. Long-term and regular users are therefore 
recommended to observe the condition of your hands and fingers. Seek medical 
attention immediately if any of the above symptoms should occur. 

 

 

1.70 

Noise (where applicable). 

1.71 

The operating noise of the machine can damage your hearing. Wear hearing 
protection such as earplugs or ear defenders to protect your hearing. Long-term 
and regular users are advised to have hearing checked regularly. Be especially 
vigilant and cautious when hearing ear protection because your ability to hear alarm 
warnings will be reduced. 

1.72 

Noise emissions for this equipment is unavoidable. Carry out noisy work at approved 
times and for certain periods. Limit the working time to a minimum. For your personal 
protection and protection of people working nearby it is also advisable for them to 
wear hearing protection. 

 

1.73 

See Certificate of Conformity section for Outdoor Noise declaration of 
conformity. 

 
 

 

1.80 

General Machine Safety. 

1.81 

Read the owner’s manual carefully to understand how to operate this machine 
properly. 

1.82 

You should 

NEVER 

use the machine when; 

1.83 

Wearing loose clothing, barefoot or sandals. 

1.84 

Under the influence of drink or drugs or as a result of having taken medication for 
cold or flu, or any other times when a possibility exists that your judgement might be 
impaired or that you might not be able to operate the machine properly and in a safe 
manner. 

1.85 

Suffering from exhaustion or lack of sleep. 

1.86 

When the ground is slippery or when other conditions exist which might make it not 
possible to maintain a steady posture. 

Содержание HY4BC31









































Отзывы: