manualshive.com logo in svg

Hyundai HX220 L, Разборка и сборка

Поделиться
Скачать
Hyundai HX220 L Скачать руководство пользователя страница 35

8-34

Apply grease

Put the spring seat (C, 624) the outer 
spring (625), and the inner spring (626) 
into compensator section of the casing.
By the same way, put the spring seat (Q, 
644) into pilot section of the casing.
The spring seat (C, 624) may fall. Apply 
grease to the spring seat (C, 624), the 
outer spring (625) and the inner spring 
(626) to prevent falling. Also the pilot 
spring seat (Q, 644) and the pilot spring 
(646) should be assembled as well.

(8)

侍

220S8MP41

Tighten cover (C, 629) with hexagon 
socket head cap screws (436).
Adjusting screw (C, 628), adjust stem (C, 
627), hexagon nut (801, 802), set screw 
(924) are fixed on cover (C, 629).
Do not loosen screw and nut. If they are 
loosened, adjusted pressure-flow setting 
will be changed.
At first, tighten C·D hexagon socket head 
cap screws (436) equally, then tighten A·B 
hexagon socket head cap screws (436) 
equally.
At spring force is strong, casing (601) and 
adjust stem (C, 627) may be damaged if 
cover (C, 629) inclined.

220S8MP32

(9)

侍

侍

侍

A

B

C

D

220S8MP30

Put the regulator to the pump. Tighten 
regulat-or with hexagon socket head cap 
screws (412, 413, 414).

This completes assembling.

(10)

Содержание HX220 L









































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды