manualshive.com logo in svg

Hyundai HX220 L, Разборка и сборка

Поделиться
Скачать
Hyundai HX220 L Скачать руководство пользователя страница 103

8-102

DISASSEMBLING TRAVEL REDUCTION GEAR

2)

Setting reduction unit (or whole propelling 
unit) on work stand for disassembling

Remove 7/16-14UNC hexagon socket head 
bolts at 3 places from cover almost equally 
apart each other, and then install 7/16-
14UNC eye bolts.

Take great care not to pinch your hand 
between parts while disassembling nor let 
fall parts on your foot while lifting them.

Removing cover

Remove the rest of 7/16-14UNC hexagon 
socket head bolts that secure cover and ring 
gear. Loosen all the socket bolts and then, 
disassemble cover.
As the cover is adhered to ring gear, 
disassemble ring gear and cover by lightly 
hammering slantwise upward using sharpen 
punch inserted between the cover and ring 
gear.

(2)

(3)

Preparation for disassembling

The reduction units removed from excavator 
are usually covered with mud. Wash outside 
of propelling unit and dry it.
Locate reducer in order for drain port to be 
at the lowest level, loosen taper screw plug 
of drain port, and drain oil from reduction 
gear.

While oil is still hot, inside of the unit may be 
pressurized.

Take care of the hot oil gushing out of the 
unit when loosening the plug.

Mark for mating
Put marks on each mating parts when 
disassembling so as to reassemble correctly 
as before.

(1)

刮

刯

侍

刮

刯

刮

到

25098TM127

25098TM128

25098TM126

Содержание HX220 L









































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды