manualshive.com logo in svg

Hyundai HX220 L, Разборка и сборка

Поделиться
Скачать
Hyundai HX220 L Скачать руководство пользователя страница 102

8-101

6.  DISASSEMBLING 

GENERAL INSTRUCTIONS

Combustibles such as white kerosene are used for washing parts. 
These combustibles are easily ignited, and could result in fire or injury.
Be very careful when using.

Internal parts are coated with gear oil during disassembling and are slippery.

  

If a part slips off from your hand and fails, it could result in bodily injury or could damage the 
park.
Be very careful when handling.

Therefore, disassembling and assembling works should be performed on the clean place where 
dusts hardly gather. 
Tools and kerosene to wash parts should also be clean and handled with great care. 

Bofore disassembling, review the sectional drawing and prepare the required parts, depending on 
the purpose and the range of disassembling.
Seals, O-rings, etc., if once disassembled, are not reusable.
There are some parts that should be replaced as a subassembly.
Consult with the parts manual in advance. 

Take great care not to pinch your hand between parts while disassembling nor let fall parts 
on your foot while lifting them. 

1)

(1)

(2)

Содержание HX220 L









































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды