manualshive.com logo in svg

Hyundai HSL1500T Track, Руководство пользователя, Страница: 58 / 80

Поделиться
Скачать
Hyundai HSL1500T Track Скачать руководство пользователя страница 58

59

4.  MAINTENANCE

4. 13  TRACK MAINTENANCE

1.

Track Inspection

Inspect the tracks daily. Look for signs of excessive
wearing, cut, and/or other damage. If damage is found
determine the cause. (Fig. 4.13A)

2.

Roller Inspection

Inspect the rollers and roller mount for signs of damage
and/or excessive wearing. If found, replace. (Fig. 4.13B).
It is normal for rollers to have tears, chunks or cuts.
Operation in an area where there is more debris will
place more inside the track and accelerate the wear.
Rollers should be replaced when rubber tire is completely
worn off on more than 3/4 of the original width. (Fig.
4.13C)

3.

Drive Lug Inspection

Check lugs for damage or  wearing. If found examine the
sprockets to find the source.

4.

Removing Debris

Remove debris from sprockets and tandem to avoid
damage to the tracks.

Fig 4.13A

Fig 4.13B

C4393

Damaged Area of Track

C4341

Roller and Mount

C4414

Fig 4.13C

Wheel Damage And Wear

Содержание HSL1500T Track

















































































Отзывы:

Нет отзывов