manualshive.com logo in svg

Hyundai HSH-121NBE, Руководство по обслуживанию

Поделиться
Скачать
Hyundai HSH-121NBE Скачать руководство пользователя страница 128

 

In  the following situations, please handle  it according to the following methods, if 
it does not work, please contact service centre  and inform the  failure 

. 

details

The wind 
blowing 
out,but the 
cooling/
heating
effect is
inefficient

The wind 
blowing 
out,but it
does not
refrigerate

Failure

Start-up 
failure

The air inlet or outlet of machine is blocked

The air inlet or outlet of machine is blocked

Compressor has three min tes protection

u

It does not  reach the set time for start up

Mistakes in temperature setting

The air filter is blocked by dust

The doors or windows are open

Mistakes in temperature setting

The power switch is released 

The battery is exhausted

Power supply failure

The fuse is burnt

Causes

Wait for the recovery of power supply

Wait or eliminate the original setting

Remove the obstruction, then restart it

Set a proper temperature, see the 
methods of application

Close the doors and windows

Set a proper temperature

Remove the obstruction

Switch on the power 

Replace the battery

Clean the air filter

Replace the fuse 

Wait 

Methods of resolution

The normal protections of the air-conditioner

1.Compressor protection

The compressor do not  restart after stop operating in 3 minutes.

the heating operation just starts                               

frost dissolving operation   

operating under low temperature

Cold wind prevention (heat pump type )

Non-air-conditioner  problem

In the heating mode, the indoor unit will  not  send wind or operate in low wind ,if the heat
exchanger of indoor unit has not reached the stipulated temperature in the following 
three states, so as to prevent the cold wind.

Frost dissolving operation (hot pump type )

 The fan of the indoor and outdoor unit will stop under frost dissolving operation.
 The time for frost dissolving varies in range of 4 to 10 minutes according to the out-

    door temperature and the frost condition.

 It is normal phenomenon that there may be steam coming out from the outdoor unit

    during the frost dissolving operation.

 

When the temperature is low and humidity is high outdoors, the heat exchanger of 
outdoor unit may frost, which may decrease the heating capacity. In such case, the air-
conditioner will stop the heating operation and convert to automatic frost dissolving,
and then resume heating after the frost dissolving finishes.

126

Содержание HSH-121NBE




































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды