a.
170 to 237 N•m (125 to 175 lbf ft) for lift
truck models
• S2.0-2.5FT
(S40-S55FT,
S55FTS)
(F187)
• H2.0-2.5FT (H40-50FT) (L177
• S50CT (A267)
• H2.0-2.5CT (H50CT) (A274)
b.
163 to 190 N•m (120 to 140 lbf ft) for lift
truck models
• S30FT, S35FT, S40FTS (E010)
• E1.50-2.00XM
(E25-35Z,
E40ZS)
(E114,F114)
• J1.60-2.00XMT (J30-40ZT) (J160)
• H1.6FT, H1.8FT, H2.0FTS (H30FT,
H35FT, H40FTS) (F001)
• E2.00-3.20XM (E45-65Z) (G108)
• J2.00-3.20XM (J40-65Z) (B416)
c.
400 to 500 N•m (295 to 370 lbf ft) for lift
truck models
• S3.0-3.5FT (S60-S70FT) (F187)
• H3.0-3.5FT (H60-70FT) (L177),
• S4.0, 4.5, 5.5FT, S5.5FTS, (S80, 100,
120FT; S80, 100FTBCS; S120FTS;
S120FTPRS) (G004, H004)
• H4.0FT5/FT6; H4.5FTS5, H4.5FT6;
H5.0-5.5FT (H80, 90, 100, 110, 120FT)
(N005, P005, R005, S005)
• E3.50-5.50XL, E4.50XLS (E70-120Z,
E100ZS) (E098)
5.
Place cylinder in a soft-jaw vise and install tilt
spacer, if equipped, and rod end on rod as noted
during removal. Lubricate threads on capscrew
with lubricant, Hyster P/N 186061. Install cap-
screw in rod end so that capscrew head is on
the inboard side of rod end. Install washer and
nut on capscrew. Washer and nut must be on
the outboard side of rod end. See Figure 5.
Tighten nut to 90 N•m (66 lbf ft).
6.
Repeat the above steps for the other tilt cylin-
der.
NOTE:
LEFT TILT CYLINDER SHOWN. TILT CYLIN-
DER AND MAST FOR LIFT TRUCK MODELS
H4.0FT5/FT6; H4.5FTS5, H4.5FT6; H5.0-5.5FT (H80,
90, 100, 110, 120FT) (N005, P005, R005, S005)
SHOWN, ALL OTHERS SIMILAR. PARTS OF MAST
OMITTED FOR CLARITY.
A.
OUTBOARD SIDE
B.
INBOARD SIDE
1. NUT
2. WASHER
3. ROD END
4. CAPSCREW
Figure 5. Rod End Installation
INSTALL
1.
Using a lifting device, place the cylinder in
mounting position on the lift truck frame. In-
stall the anchor pin. Install the retainer and
capscrew. See Figure 2. Lubricate the threads
on the capscrew with lubricant, Hyster P/N
186061, and tighten capscrew to:
Tilt Cylinder Repair
2100 SRM 1139
10
