background image

Vortex 3 Voice Effects Unit, 

Hyperdyne Labs LLC 

 

 

17

CHEAT SHEET (PRINT OUT) 

 
 
 
 

PROG 
button 

presses 

Voice board feature 

(DARK LORD)

 

Default 
setting 

1x 

 

Increase VOX on threshold (5 settings, 0 default) 
Table values: ([Lowest], low, medium, med-high, high) 

Lowest 

2x 

Increase VOX off threshold (5 settings, 0 default)   
Table values: ([Lowest], low, medium, med-high, high) 

Lowest 

3x 

Auto talk squelch timeout (mic open time) in VOX 
mode  
Table values:  (3, 4, [5], 6, 7, 8) sec  

5 sec  

4x 

  

PTT enable/[disable] 
PTT enabled:  Must use remote button to open mic 
PTT disabled:  VOX mode is active and will open mic  

Disabled 

5x 

Change pitch of your voice (smaller number is deeper) 
Table values:  (2.75, 2.5, [2.25],  ...,1.25, 1.0)  8 settings 

1.5 

6x 

Change bulk mic gain  
Table values:  (15, 20, 25, [30], 35, 40) dB 

30 dB  

7x 

Change fine mic gain 
Table values:  (0, 1, 2, 3, 4) dB 

0 dB 

8x 

[Enable]/disable breath FX 

Enabled 

9x 

Change breath volume gain 
Table values:  (0.1, [0.2], 0.5, 0.75, 1.0) 

0.2 

10x 

Change silence gap between breath playback 
Table values:  ([2], 3, 4, 5, 6 sec) 

2 sec 

11x 

Change amount of helmeted effect (low, med, [high]) 

high 

12x 

Reset all parameters to factory defaults 

Reboots  

 

 
 

PTT 

button 

presses 

Board responds with… 

(DARK LORD)

 

Enables/disables breathing FX 

Cycles to next breathing sound for 
playback (if breath FX enabled) 

Play out WAV audio 
"VMUSIC1.WAV" 

Play out WAV audio 
"VMUSIC2.WAV" 

Play out WAV audio 
"VMUSIC3.WAV" 

Enable/disable PTT mode 

Hold 

button in 

> 1 sec 

Opens mic if PTT mode enabled 

 

Содержание Vortex 3 Dark Lord


















Отзывы: