Hydthc XPTHC-4, Руководство пользователя

Страница: 14 / 25

地址：深圳市南山区中山园路 1001
2.4.1
、
Parameters details
Common parameters
Parameter
No
Parameter
Name
Default
value
ARC
setting
130
Piercing
time
1
IHS height 0.4
Special parameter
dynamic
pierce
height
0
ARC
sampling
logic
0
Limit logic 0
Corner
signal logic
0
深圳市宏宇达数控技术有限公司
1001 号 E4-6C(TCL 国际 E 城) TEL：755-26625800 FAX
-14-
Default Unit Range Function and Description
V 50~25
0
Setting arc voltage mode effective. Set
arc voltage before cutting, it can be adjusted by
“UP” or “DOWN”to change the setting arc voltage
during cutting.
10mS 00~60 When THC sends the arc
then will delay the lead in arc voltage to THC,
thus it will has the anti
THC.
This parameter is also for dynastic pierce setting.
It’s set via the time of the
as if it needs 3s for the Arc start process, then it
should be set to 30.
10mS 05~99 This IHS height can be g
the operation panel. It r
torch lifter.
10mS 00~99 This height is for the plasma arc piercing
to protect the torch consumables.
0
，
1
1
、
When set “0”, the setting arc voltage by “P1”
set as for the cutting height during auto work.
2
、
when set “1”, via the CNC’s corner signal,
when the THC is opened the AUTO function,
and take the actual arc voltage as the cutting
arc voltage during auto work. In this mode, it’s
required the CNC with high speed up to the
setting speed to open the auto mode, this is
the at the IHS height during cutting, it can be
used for bevel cutting.
During the cutting, it could be adjust the “UP”
and “DOWN” to change the arc voltage
sample, the cutting height won’t be changed
during the whole cutting work until loose Arc.
0
，
1 0
：
limit Normally open
closed.
When the connection is not match to the “P6”
parameter’s setting, then the UP_limit and
Down_limit LED light will be turned on.
0
，
1 0
：
corner logic close auto
open auto
Note
：
This signal needs to
深圳市宏宇达数控技术有限公司
26625800 FAX：755-26729960
Function and Description
rc voltage mode effective. Set the setting
arc voltage before cutting, it can be adjusted by
“UP” or “DOWN”to change the setting arc voltage
arc start signal to plasma,
then will delay the lead in arc voltage to THC,
has the anti-interference function to
This parameter is also for dynastic pierce setting.
the Arc start to Arc ok. Such
as if it needs 3s for the Arc start process, then it
This IHS height can be got from the IHS test on
the operation panel. It relates to the speed of the
is for the plasma arc piercing height,
to protect the torch consumables.
the setting arc voltage by “P1”
for the cutting height during auto work.
via the CNC’s corner signal,
when the THC is opened the AUTO function,
and take the actual arc voltage as the cutting
arc voltage during auto work. In this mode, it’s
required the CNC with high speed up to the
setting speed to open the auto mode, this is
the at the IHS height during cutting, it can be
used for bevel cutting.
During the cutting, it could be adjust the “UP”
and “DOWN” to change the arc voltage
sample, the cutting height won’t be changed
during the whole cutting work until loose Arc.
limit Normally open
；
1
：
limit Normally
When the connection is not match to the “P6”
parameter’s setting, then the UP_limit and
Down_limit LED light will be turned on.
close auto; 1: corner logic
signal needs to be matched with CNC