14
Refer to Owner’s Manual for complete details
LIquID CRYSTAL DISPLAY (LCD)
Continually provides feedback on the
operating status of the hot tub.
Icons indicate various functions and
programming information.
LCD INvERT
This feature inverts the LCD readout for convenient viewing
from inside the hot tub. To invert the readout,
Platinum Series: press
or
then
Titanium Series: press
To return the LCD readout to normal viewing (from outside
of the hot tub), repeat.
ToPSIDE PANEL LoCk FEATuRES
TEMPERATuRE LoCk
The temperature lock feature prevents unauthorized
temperature adjustment of the hot tub water. When the
temperature lock is activated, all automatic functions will
continue to operate normally.
The following pads must be pressed within 3 seconds of
each other to activate the lock:
then
then P1
then
TEMPERATuRE uNLoCk
The following pads must be pressed within 3 seconds of
each other to deactivate the lock:
then
then P1
then
When locked, the TL (Temperature Lock) light on the left side
of the topside control panel will illuminate. Only the topside
control panel temperature pads will be deactivated.
ToPSIDE PANEL FuLL LoCk
The topside panel lock feature prevents unauthorized use of
the hot tub controls. When the topside control panel lock is
activated, all automatic functions will continue to operate
normally.
The following pads must be pressed within 3 seconds of
each other to activate the lock:
then P1
then
ToPSIDE PANEL uNLoCk
The following pads must be pressed within 3 seconds of
each other to deactivate the lock:
then P1
then
When locked, the PL light (Panel Lock) on the left side of
the topside control panel will illuminate. All of the topside
control panel pads will be deactivated except for the
pad.
STANDbY / DRAIN ASSIST
The standby/drain assist feature stops the system from
operating automatically, allowing for convenient filter
cartridge removal and for safe draining of the hot tub. The
following pads must be pressed within 3 seconds of each
other.
The system will automatically exit Standy Mode after 1
hour and resume normal operating functions.
Press
then the P2
pad and the display will flash:
SBY
(
Platinum series
)
STANDBY
(
Titanium series
)
If the system is heating when Standby mode is activated,
will flash on the display and the pump will continue
to operate for 15 seconds to allow the heater to cool off
before stopping.
All functions will turn off, but P1 low speed can be
activated (by pressing the P1
pad) to facilitate draining
the hot tub and the display will show
(
Platinum series
)
DRAINING
(
Titanium series
)
Press any pad other than the P1
pad to return the system to
normal operation. See section DRAINING YOUR HOT TUB for
detailed instructions.
LED MooD LIGHTING
Press the
pad on the topside control to start the
selection of LED lighting modes. Pressing the
pad
on/off within 3 seconds cycles through the various ‘light
shows’. When the LED lighting is turned off for more than 5
seconds, then turned back on, the system will resume the
last ‘light show’. The system will automatically turn off the
mood lighting after 4 hours.
bLoWER
oPTIoNAL – FACToRY INSTALLED
Press this pad to turn the blower on and off.
The system will automatically turn off the blower after
15 minutes.
ozoNAToR
oPTIoNAL
The ozonator operates during FILTER CYCLES and CLEAN UP
CYCLES only. The display will show the
O
3
icon while the
ozonator is operating.
Pressing any pad on the topside control panel will suspend
ozonator function for 1 hour.
FREEzE PRoTECTIoN
If the temperature sensor detects a drop to 4˚C (39˚F) within
the heater chamber, the system automatically activates
the pumps to provide freeze protection. The pumps will
operate until the temperature reaches 5˚C (41˚F) before
returning to normal system mode.
