background image

10

Refer to Owner’s Manual for complete details

PuMP / JETS FuNCTIoN

Press this pad to activate the pump

1st press   – turns on low speed 

2nd press  – turns on high speed 

3rd press  – turns off pump 

When low speed is already operating, the 1st press of the  

 pad puts the pump directly into high speed.

Low speed starts automatically every 30 minutes to measure 

water temperature (in STANDARD mode only – see mODE 

FUNCTION),  when  a  filter  cycle  is  activated,  or  when  a 

freeze condition is detected. 

When the blower (optional) is manually activated, the pump 

low speed is automatically activated and operates until the 

blower  times  out.  If  the  blower  is  turned  on  even  briefly, 

and  then  turned  back  off,  low  speed  will  operate  for  a 

minimum of 2 minutes.

PuMP AuToMATIC TIME-ouT

High speed 

– 15 minutes

Low speed  

– 4 hours 

FILTER CYCLES

The system will automatically activate the pump low speed 

to filter the water either once or twice each day, and can 

be programmed by the user. The first filter cycle begins 6 

minutes  after  the  spa  is  initially  powered  up.  The  second 

filter cycle begins 12 hours after the start of the first filter 

cycle. The filter cycle duration - length of time the pump 

low runs - is programmable from 1 to 12 hours (F1 to F12). 

The factory default is 2 hours, twice daily.

PRoGRAMMING FILTER CYCLES

To change the factory default filter cycle settings

Press 

 then 

 - the current filter cycle duration will 

be displayed

Press 

 again to adjust the filter cycle duration

Press 

 to exit programming mode and save changes.

bLoWER 

oPTIoNAL – FACToRY INSTALLED

   Press this pad to turn the blower on and off.

The  system  will  automatically  turn  off  the  blower  after  

15 minutes.

PuRGE CYCLES 

bLoWER oNLY

The  system  automatically  activates  the  blower  for  30  

seconds at the beginning of each filter cycle to introduce 

fresh, sanitized water into the blower plumbing circuit.

MoDE FuNCTIoN

A  combination  of  keypads  is  used  to  change  hot  tub  

operation to either ‘STANDARD’, ‘ECONOMY’ or ‘SLEEP’ mode. 

PRoGRAMMING MoDE FuNCTIoN

Press 

 then 

 - the current mode setting will flash 

on the display

Press  

 then 

 repeatedly to select mode

STANDARD MoDE

The system automatically starts the pump low speed every  

30  minutes  to  measure  water  temperature,  and  maintain 

the set temperature. The display will show 

 briefly, then  

the  last  measured  water  temperature.  The  current  water 

temperature  is  displayed  only  after  the  pump  has  been 

operating for at least 2 minutes.

ECoNoMY MoDE

The  system  will  heat  to  the  set  temperature  only  

during the filter cycles. The display will show 

 when the  

temperature  is  non-current.  When  the  temperature  is  

current,  the  display  will  alternate  between 

  and  the 

water temperature.

SLEEP MoDE

The  system  will  heat  to  within  10˚C  (20˚F)  of  the  set  

temperature only during filter cycles. The display will show 

 until the mode is changed. 

STANDbY / DRAIN ASSIST 

The  standby/drain  assist  feature  stops  the  system  from  

operating  automatically,  allowing  for  convenient  filter 

cartridge removal and for safe draining of the hot tub. The 

following  pads  must  be  pressed  within  3  seconds  of  each 

other.

   

 

 

 

 

 

Press 

  then  the 

  pad  -  the  display  will  

flash 

.

If the system is heating when Standby mode is activated,  

 will flash on the display and the pump will continue 

to operate for 15 seconds to allow the heater to cool off 

before stopping.

   

 

 

 

 

All functions will turn off, but the pump low speed can be 

activated  (by  pressing  the 

  pad)  to  facilitate  draining 

the hot tub - the display will show 

DN.

 

 

Press any pad other than the 

 pad to return the system 

to normal operation. 

See DRAINING YOUR HOT TUB for detailed instructions.

Содержание Gold Series 20A

















Отзывы: