manualshive.com logo in svg

HydroAir P-38 Series, Руководство по эксплуатации

Поделиться
Скачать
HydroAir P-38 Series Скачать руководство пользователя страница 6

Introduction

 

Hydro-Air P-38

 

 

2 

pH / ORP Analyzer 

2.0 

Introduction 

 

2.1. 

General Information 

 

 

Notice

 

Indicates  essential  information  regarding  operation,  calibration  or  anything  which  is 
considered as good practice or handling of the products. 

 
The  manufacturer  will  not  be  liable  and  responsible  for  any  direct,  indirect, 
incidental  or  consequential  damages  due  to  any  defect  or  omission  in  the 
operations manual. The manufacturer reserves the right to alter the content in the 
operations manual as well as the products without any notification. Please contact 
the  manufacturer  to  request  the  latest  and  revised  editions  of  the  operations 
manual. 
 
Unpacking, setting, installing and operating of the product require comprehensive 
knowledge and understanding of the entire operations manual. Please take note to 
all danger, warning and notice signs and details. Negligence of the danger, warning 
and notice signs could increase the risk of serious injury to the product’s operator 
or even inflicting damage to the products. Do not install, calibrate or operate this 
product in any manner other than that specified in the operations manual. 
 

2.2. 

Safety Information 

 

DANGER!

 

[Signage] 

Neglecting the signs may result in death or at least serious injury 
to the operator. 

 

WARNING!

 

[Signage] 

Neglecting the signs may result in mild or at least minor injury to 
the operator. 

 

 

Содержание P-38 Series





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды