manualshive.com logo in svg

Hydro WQM-100, Инструкция по эксплуатации, Страница: 11 / 28

Поделиться
Скачать
Hydro WQM-100 Скачать руководство пользователя страница 11

IV.  EXPLANATION OF OPERATION MODE SCREENS

Main Screen:

  This screen will display the live readings for installed and active electrodes (e.g. pH, ORP 

and/or conductivity) and temperature sensors.  The values shown in extra-large font size are live readings.  A 
value may show in red color if there is an active Alarm condition for the respective electrode.

pH Chart:

  This screen shows curves which graphically depict pH values for active pH sensors over a user-

adjustable time period. The pH chart will not be present if neither channel 1 nor channel 2 is set for pH.

ORP Chart:

  This screen shows curves which graphically depict ORP values for active ORP electrode over 

a user-adjustable time period.  The ORP chart will not be present if neither channel 1 nor channel 2 is set for 
ORP.

Conductivity Chart:

  This screen shows curves which graphically depict conductivity values for active 

conductivity electrodes over a user-adjustable time period.  The Conductivity chart will not be present if no 
conductivity electrodes are present.

Temperature Chart:

  This screen shows curves which graphically depict temperature values for active 

thermistors over a user-adjustable time period.

Alarm Status Screen:

  This screen will show a list of current alarm conditions for active probes and sensors.  

Typically, a non-normal alarm condition will be shown in red color.

Access Screen:

  In addition to allowing access to the WQM-100 Confi guration screen (after adjusting the 

password value to “100”), users can initiate an “I/O Hold” from this screen.

11

Содержание WQM-100





























Отзывы:

Нет отзывов