background image

8

TAbLE 1:  relay designations for Vaporizer Alarms and relays

Parameter

Terminal

Gas Pressure

AO1

Gas Temperature

AO2

Superheat Temperature

AO3

Control Water Temperature

AO4

Auxiliary Water Temperature

AO5

Expansion Chamber Switch

DI3

Pressure Relief Valve Switch

DI4

* Wired from the factory.

NOTe:  The electronic pressure reducing valve relays are energized relays and thus recommended 
normally open.

TAbLE 2:  4-20 Output designations

NOTe:  All outputs must also be wired to the appropriate V- (GND) terminal.

 

  4.3  Modbus Information

 

  The VPH-10000 can also communicate with a SCADA system using Modbus RS-485 communication.  

The baud rate, node number and data format of the VPH-10000 must match that of the master SCADA 
system.  See Section III.5 for information on how to accesses and edit these features.  A table of 
Modbus integers and their corresponding parameters can be seen in Table 3.  For more information 
on configuring Hydro Instruments equipment onto SCADA systems, please refer to the Modbus 
Installation and Instruction manual.

Vaporizer Alarm/Relay

Board Number

Relay Number

Recommended Wiring

Electronic Pressure

Reducing Valve 1

CB-8RELAY

1

N.O.

*Refill Solenoid

CB-8RELAY

2

N.O.

*Circulation Pump

CB-8RELAY

3

N.C.

*Magnetic Contactor

CB-8RELAY

4

N.O.

Electronic Pressure

Reducing Valve 2

CB-8RELAY

5

N.O.

Superheat Alarm

CB-8RELAY

6

N/A

High Pressure Alarm

CB-8RELAY

7

N/A

Water Level Alarm

CB-8RELAY

8

N/A

Low Water Temperature Alarm

CB-2RELAY

1

N/A

High Water Temperature Alarm

CB-2RELAY

2

N/A

Содержание VPH-10000 Series



































Отзывы: