Hydro Instruments VPH-10000 Series Скачать руководство пользователя страница 26

Страница: 26 / 34

V. TrOubLESHOOTIng:

Refer to Table 5 for common problems and troubleshooting techniques for the vaporizer system. For

questions please consult Hydro Instruments.

TAbLE 5: Troubleshooting Chart

Problem

Probable Cause(s)

Corrective Action

• Liquid chlorine in

vacuum piping

• Damaged vacuum

piping and equipment
(vacuum regulator)

• Demand has exceeded design capacity

• Fouling of pressure chamber
• Faulty chlorine temperature or

pressure sensor did not allow PRV to
close

• Supply pressure too high
• Low water temperature/level and

failed switches

• By-pass piping through PRV is open

• Lower capacity to within design flow

rate

• Clean inside and outside of chlorine

pressure chamber (follow appropriate
shut down and cleaning procedures)

• Reduce cylinder pressure
• Check and replace equipment.

• Check that by-pass piping is not open

• High pressure in

chlorine pressure
chamber

• Inlet chemical pressure is too high

• Valves closed before and after

vaporizer

• Blockage in supply line

• Lower the room temperature or

decrease the amount of gas padding.

• Open the supply valves

• Evacuate and shut down system.

Clean/replace piping

• Leaking chlorine

through pressure relief
valve (pressure switch
activated)

• Rupture disc has burst due to

overpressure

• Follow long term shutdown to

evacuate chemical. Replace rupture
disc

• Pressure switch

activated from
expansion chamber
assembly

• High pressure in

liquid pipeline

• Rupture disc has burst due to

entrapment of liquid chlorine

• Follow the long term shut down

procedure and replace the broken
rupture disc

• High water

temperature

• Failed/improperly wired temperature

control circuit

• Failed/improperly wired heater

• Check wiring. Replace equipment if

correct

Содержание VPH-10000 Series



































Результаты поиска

Содержание VPH-10000 Series

Отзывы:

Похожие инструкции для VPH-10000 Series

Бренды по названию

Популярные бренды

Hydro Instruments VPH-10000 Series, Инструкция по эксплуатации

Результаты поиска

Содержание VPH-10000 Series

Отзывы:

Похожие инструкции для VPH-10000 Series

Бренды по названию

Популярные бренды