manualshive.com logo in svg

HydraMaster Chem-Dry PowerHead, Руководство пользователя

Поделиться
Скачать
HydraMaster Chem-Dry PowerHead Скачать руководство пользователя страница 45

9-1:  Repair

  Harris Research, Inc. 

Chem-Dry

®

 

PowerHead

®

9 - Repair

FELT VACUUM SEAL 

The felt vacuum seal plays an important part in the optimum performance of your 
Chem-Dry PowerHead. If the part is worn or unlubricated, it will not form a proper seal. 
Lack of a proper seal will impair the vacuuming 
capabilities of the unit and therefore leave 
behind more water in the carpet than is 
desirable.

To replace the vacuum seal:

1.  First, remove the vacuum head assembly 

as previously described.

2.  Using a pocket knife or similar tool, 

carefully pry the seal up and lift it out. If 
the seal appears worn or glazed so that 
it will not lubricate well, turn it over (see Figure 9-1). If that does not work, or if it is 
damaged, replace it with a new seal.

3.  Chem-Dry recommends changing the felt seal after 10 hours of use. Replace it with 

a seal that has been pre-soaked in a quality 30 weight 
SAE motor oil .

4.  Press the seal in place and saturate it with the motor oil. 

If a flattened seal will be re-used, place the used seal in 

an oil bath to rejuvenate it.

For the seal’s oil bath, use a small receptacle the size 

and shape of a tuna fish can (see 

Figure 9-2; a plastic 

container for this purpose is included in the Harris 
Research Service Kit.

Figure 9-1.  Carefully Pry 

 Seal Up and Lift Out

Figure 9-2.  Use Can to 

Hold Oil for Seal

Fluffy, Usable Side

Compressed, 

Non-usable Side

Содержание Chem-Dry PowerHead



















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды