manualshive.com logo in svg

HydraMaster Chem-Dry PowerHead, Руководство пользователя

Поделиться
Скачать
HydraMaster Chem-Dry PowerHead Скачать руководство пользователя страница 15

4-1:  Operating Instructions

  Harris Research, Inc  

Chem-Dry

®

 

PowerHead

®

4 - Operating Instructions

PREPARATION

Handle Adjustment

Push the clamp forward to loosen 
the linkage. Adjust the handle to a 
comfortable height. Pull clamp back 
to lock in place.

Most technicians have found 
better control and less fatigue 
when the handle is in a low 
position - just around the hip 
line. There is an ideal position 
for each person which will 
ensure the PowerHead will do 
the work for you.

Solution and Vacuum Hose 
Connections

Your PowerHead is equipped with one 440 stainless steel male quick connect for the 
solution hose and an 1 ½” vacuum hose inlet (refer to Figure 4-1). The vacuum inlet 

requires a 1 ½” I.D. and a 2” O.D. vacuum hose for proper air flow.

The vacuum hose must be in good condition to ensure maximum airflow. 

Electrical Cord Connection

The 50 ft electrical cord on your PowerHead is a detachable three-prong grounded line 
requiring a three-prong, 15 Amp receptacle. A three-prong to two-prong adapter may be 
used, providing its ground wire is properly attached to a grounded terminal. 

 

Do not, under any circumstances, remove the ground prong from your PowerHead 
power cord. Serious injury or death may result. 

Figure 4-1.  Solution and Vacuum 

Hose Connections

Solution Hose  

Quick Connect

1 1/2” Hose  

Inlet

Содержание Chem-Dry PowerHead



















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды