manualshive.com logo in svg

HydraMaster Chem-Dry PowerHead, Руководство пользователя

Поделиться
Скачать
HydraMaster Chem-Dry PowerHead Скачать руководство пользователя страница 21

5-3:  Cleaning Information

  Harris Research, Inc. 

Chem-Dry

®

 

PowerHead

®

CLEANING HINTS

1.  Most cleaners customarily clean their way out of an 

area or room. With the PowerHead, it is possible to 
clean into an area or room, as shown in Figure 5-2, 
so that the hoses are dragged behind you during 
the cleaning process rather than kicked out of the 
way as you back out of an area. The “cleaning 
into” method works especially well in hallways or 

confined areas.

2.  The PowerHead is a very aggressive carpet 

cleaning machine and will leave the carpet with a 
freshly-cleaned appearance. The carpet should be 
brushed or groomed after the cleaning process to 
remove any swirl marks left behind.

The PowerHead has been very successful in restoring badly matted traffic lanes in front 

of doorways and sofas. Even pivot areas can be brought back to life again, in most cases. 
“Cornrowing” in hallways can also be eliminated with minimal effort.

Figure 5-2.   Clean into an 

Area or Room

Содержание Chem-Dry PowerHead



















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды