Hydac FCU 1310 Скачать руководство пользователя страница 126

Страница: 126 / 148

10 | Finding / rectifying errors

HYDAC FILTER SYSTEMS GMBH

126 / 148

BeWa FCU1310 3371346g en-us lq

Disruption / error

LED
Status LED
Display
Error code

Status /
Possible causes

Solution

LED: Green

Status LED

Display:

Error code: 0

The FCU is ready for oper-
ation.

You can take measurements.

LED: Red

Status LED:

Display:

Error code: 2

The FCU is below its mea-
surement range
< ISO 9/8/7.

It is currently not possible
to determine the cleanli-
ness of the oil or its flow
rate.

You can make further mea-
surements.

LED: Red

Status LED:

Display:

Error code: 2

It is not possible to deter-
mine the flow rate.

The FCU is in an undefined
state.

Switch the pump on.

Wait for a few measurement
cycles until measured values
are again shown.

LED: Red

The FCU is above its range
of measurement
> ISO 25/24/23.

Filter the oil to improve its
cleanliness.

Содержание FCU 1310





















































































































































Результаты поиска

Содержание FCU 1310

Отзывы:

Похожие инструкции для FCU 1310

Бренды по названию

Популярные бренды

Hydac FCU 1310, Инструкция по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание FCU 1310

Отзывы:

Похожие инструкции для FCU 1310

Бренды по названию

Популярные бренды