Hydac FCU 1310 Скачать руководство пользователя страница 119

Страница: 119 / 148

HYDAC FILTER SYSTEMS GMBH

Performing maintenance | 8

BeWa FCU1310 3371346g en-us lq

119 / 148

NOTICE

Wrong installation / wrong flow direction of the flow control

valve

Flow control valve is not working

Pay attention to the direction of flow when installing the
flow control valve.

Remove coupling (A) using a wrench (

= 22 mm) by

turning it counterclockwise out of the screw fitting (D).

Unscrew the strainer (B) counterclockwise with a screw-

driver or the special tool (see

Finding accessories [

}

135]

chapter).

Clean strainer (B) and then blow it out with compressed

air.

Also unscrew the flow control valve (C) counterclock-

wise with a screwdriver or the special tool (see

chapter).

To install the new flow control valve (C), screw it firmly

clockwise into the union (D) with a screwdriver or the

special tool.

Screw the strainer (B) clockwise into the union (D) using

a screwdriver or the special tool.

Then check the sealing ring on the coupling (A) for dam-

age. Replace it if necessary.

Turn the coupling (A) in a clockwise direction and tighten

to 25 Nm.

Содержание FCU 1310





















































































































































Результаты поиска

Содержание FCU 1310

Отзывы:

Похожие инструкции для FCU 1310

Бренды по названию

Популярные бренды

Hydac FCU 1310, Инструкция по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание FCU 1310

Отзывы:

Похожие инструкции для FCU 1310

Бренды по названию

Популярные бренды