HYDAC FILTER SYSTEMS FCU1315 Скачать руководство пользователя страница 73

Страница: 73 / 185

7 |

HYDAC FILTER SYSTEMS

64 /

BeWa FCU1315 4168086b

Displaying measured variables

The measured variables supply you with information regarding

the degree of cleanliness, the water saturation and the temper-

ature of the hydraulic system under investigation. The mea-

surement variables ISO, SAE and NAS are calibrated. They in-

dicate a measured value with an accuracy of ± ½ ISO code in

the calibrated range.

3.1.

Measured variable - ISO

The measured variable is updated depending on the set mea-

suring time. The presentation appears as a 3-digit ISO code.

Example: ISO code 20.18.15

3.2.

Measured variable - SAE

The measured variable is updated depending on the set mea-

suring time. The presentation takes the form of a channel of

the SAE class. Example: SAE class A = 13.4

3.3.

Measured variable - NAS

The measured variable is updated depending on the set mea-

suring time. The presentation takes the form of a channel of

the NAS class. Example: NAS class, channel 15-25 = 13.2

3.4.

Measured variable – Water Saturation

The integrated AquaSensor continuously measures the satura-

tion. The measured value is shown on the display as the water

saturation of the fluid, expressed as percentage saturation. Ex-

ample: 19.3% water saturation

3.5.

Measured variable – Temperature

The integrated AquaSensor continuously measures the fluid

temperature. The output as Celsius °C or Fahrenheit °F can be

set under

. Example: Temperature = 37.8 °C

Содержание FCU1315


























































































































































































Результаты поиска

Содержание FCU1315

Отзывы:

Похожие инструкции для FCU1315

Бренды по названию

Популярные бренды

HYDAC FILTER SYSTEMS FCU1315, Инструкция по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание FCU1315

Отзывы:

Похожие инструкции для FCU1315

Бренды по названию

Популярные бренды