HYDAC FILTER SYSTEMS FCU1315 Скачать руководство пользователя страница 135

Страница: 135 / 185

HYDAC FILTER SYSTEMS

Performing maintenance

BeWa FCU1315 4168086b

123 /

NOTICE

Operation without a strainer

The flow control valve in the high-pressure adapter will be
damaged / destroyed

Never use the high-pressure adapter without a strainer

The suction strainer in the high-pressure adapter must be

cleaned regularly

1. Remove the measurement coupling (A) from the

threaded joint (D) with a wrench (

= 22 mm) by turn-

ing it counterclockwise.

Then unscrew the strainer (B) counterclockwise with a
screwdriver or the special tool (see chapter

2. Clean strainer (B) and then blow it out with compressed

air.

3. To fit the strainer (B), screw it in, clockwise, to union (D)

using a screwdriver or the special tool.

4. Then check the sealing ring on the coupling (A) for dam-

age. Replace it/them if necessary.

5. Screw in the coupling (A) in clockwise direction and

tighten it to 25 Nm.

⇨

The cleaning / replacement of the strainer is complete.

The high-pressure adapter is ready for operation.

B Strainer

D Screw connection

Содержание FCU1315


























































































































































































Результаты поиска

Содержание FCU1315

Отзывы:

Похожие инструкции для FCU1315

Бренды по названию

Популярные бренды

HYDAC FILTER SYSTEMS FCU1315, Инструкция по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание FCU1315

Отзывы:

Похожие инструкции для FCU1315

Бренды по названию

Популярные бренды