Hyco RHO IN44T Скачать руководство пользователя страница 3

3

Thank you for purchasing a Hyco instantaneous water heater. Instantaneous
water heaters are very energy efficient since they only consume energy
when they are used and so have no standing losses. The IN44T & IN60T
models are mains pressure instantaneous water heaters with external 
electronic temperature control. Bare wire heating systems offer rapid heat
up times and a near instant supply of hot water. The heaters are intended 
for handwashing applications and should be used in conjunction with spray
head taps. Please read and understand these instructions before commencing
installation, and leave them with the user when installation is complete.

1. Important safety points

•  

The appliance must only be connected to a single phase supply.

•  

Isolate electrical and water supply before installation.

•  

Electrical installation must be carried out by a qualified electrician in accordance 

with the latest edition of the IEE wiring regulations.

•  

Only connect the appliance to a power supply that conforms to the specification 

stated on rating plate.

•  

The appliance must be earthed at all times.

•  

The appliance must be permanently connected to the electrical supply through 

an isolating switch with a contact separation of no less than 3mm in all poles.

•  

Do not use the appliance if there is any possibility of the water supply being frozen.

•  

Never remove the cover of the appliance without first isolating it from the electrical 

power supply.

•  

This appliance can be used by children aged from 8 years and above and persons 

with reduced physical, sensory or mental capabilities or lack of experience and 

knowledge if they have been given supervision or instruction concerning use of the   

appliance in a safe way and understand the hazards involved. Children shall not play    

with the appliance. Cleaning and user maintenance shall not be made by children   

without supervision.

•  

Do not use a supply with incoming water temperatures greater than 60

0

C.

IN44T & IN60TNEW_Layout 1  02/06/2015  14:37  Page 3

Содержание RHO IN44T













Отзывы: