MP34.4315
06MAY19
ROOM 1 EXTEND/RETRACT/STATUS
WARNING:
OPERATING A ROOM WITH ANY ROOM LOCKING,
CLAMPING OR MANUAL RETRACTING DEVICES ATTACHED OR
ENGAGED CAN CAUSE PERSONAL INJURY AND VEHICLE DAMAGE
IT IS THE OPERATOR’S RESPONSIBILITY TO ENSURE THAT ALL ROOM
ALL ROOM LOCKING, CLAMPING OR MANUAL RETRACTING DEVICES
ARE DETACHED OR DISENGAGED BEFORE OPERATING THE ROOM.
1. Unlock all room-locking devices.
NOTE: If a MANUAL RETRACT device is attached to
the room remove it before extending the room.
WARNING:
KEEP PEOPLE AND OBSTRUCTIONS
CLEAR OF ROOM WHEN OPERATING.
NOTE: Make sure there is adequate clearance to fully
extend the room.
2. To extend the room, press and hold the EXTEND ROOM
button until the room is fully extended. The EXTEND ROOM
LIGHT will flash while the button is being pushed.
NOTE: Hold the switch to "EXTEND" three or four seconds after the room
is fully extended. This assures proper pressurization of the cylinders.
During normal operation of the room, do not reverse direction of the
room until the room is fully extended. If necessary, the direction of
the room may be reversed, but watch for binding of the room. If the
direction of the room has been reversed, DO NOT re-extend the room
IMPORTANT:
If either side of the room stops moving, release the room control
switch immediately. DO NOT force the room. DO NOT reverse direction
NOTE: Releasing the ROOM CONTROL SWITCH will
halt the operation of the room.
Do not hold the ROOM CONTROL SWITCH in the "EXTEND"
position for more than ten seconds after the room is fully extended or stops
moving.
ROOM RETRACT PROCEDURE
retracting the hydraulic leveling system.
It is recommended to retract room extensions before
light will flash while the button is being pushed.
pressurization of the cylinders.
has been fully extended.
after the room is fully retracted. This assures proper
Hold the switch to "RETRACT" three or four seconds
of the room, do not reverse direction of the room until
the room is fully retracted. If necessary, the direction
of the room may be reversed, but watch for binding of
the room. If the direction of the room has been
reversed, DO NOT retract the room until the room
CLEAR OF ROOM WHEN OPERATING.
button until the room is fully retracted. The RETRACT ROOM
1. To retract the room press and hold the RETRACT ROOM
WARNING:
NOTE:
During normal operation
KEEP PEOPLE AND OBSTRUCTIONS
Do not hold the ROOM CONTROL SWITCH
in the "RETRACT" position for more than ten seconds
after the room is fully retracted or stops moving.
If either side of the room stops moving, release the
room control switch immediately. DO NOT force the
room. DO NOT reverse direction of the room, contact
HWH Customer Service for assistance 1-800-321-3494.
NOTE: Releasing the ROOM CONTROL SWITCH will
3. If the room will not retract see the MANUAL ROOM
IMPORTANT: Room-locking devices should be locked
RETRACT PROCEDURE.
while traveling.
2. Engage all room-locking devices.
halt the operation of the room.
NOTE:
IMPORTANT:
RETURN TO ROOM PAGE BUTTON: This button will
return the screen to the ROOM SELECTION page.
NOTE: If the park brake is released while operating a
UNDERSTAND OPERATOR’S MANUAL BEFORE USING. BLOCK FRAME AND TIRES
CAUTION!
SECURELY BEFORE REMOVING TIRES OR CRAWLING UNDER VEHICLE.
LIGHT
RETRACT ROOM
EXTEND ROOM
RESET
(ROOM LOCATION)
ROOM # OPERATION
RETURN TO
ROOM PAGE
HOME
HWH SYSTEMS CONTROL
R
STOP
OPERATING PROCEDURES
until the room has been fully extended.
of the room, contact HWH Customer Service for assistance 1-800-321-3494.
IMPORTANT: DO NOT USE A ROOM EXTENSION
SUPPORT WHEN THE VEHICLE IS SUPPORTED BY
THE LEVELING SYSTEM.
room, the screen will return to the home page.
Refer to vehicle manufacturer for proper sequence of
room extension and leveling system operation.
