Hwayuan Electric LGK-40/63IGBT Скачать руководство пользователя

Страница: 14 / 20

LGK-40/63IGBT OPERATOR’S MANUAL

7. Connection of cutting ground wire

Connect the fast connector of cutting ground wire with the outlet marked with Cutting

Ground Wire on the front panel and screw down it clockwise. The other end of the cutting
ground wire is connected to workpiece firmly.



Operation method

1. Security notes

2. Turn on the power switch after installation and connection. Then the power indicator lamp

is ON.

3. Start gas supply equipment and turn on the gas supply switch, the power indicator lamp on

the panel is ON. If the gas pressure is less than 0.25Mpa, the lamp will be OFF, then the gas
source should be checked.

4. Gas control switch switches to Check air. Adjust the pressure Adjusting knob of gas filter on

Notes

Operation strictly accordant with the following steps

Notice

Electric shock may
hurt or even kill
man.

Cutting may cause fire or explosion



Splashes may ignite flammable materials

nearby. Those materials should be 10m away

from the working place.



Shut

off

the

power

during

connection



Do not touch the conducted parts

Fume & dust is harmful.



Do not breathe in the fume and dust

caused by cutting



Clean up the oil spot on work piece.



Keep fresh air in working place



Fume extraction equipment should

be prepared.

Arc may hurt your eyes and skin.



Strong arc may hurt your eyes.



Ultraviolet radiation generated by arc may hurt

skin and eyes. Please wear shielded guard

when cutting.

Overheated part may hurt
your skin.



Do not touch the overheated part on

the work piece.



Do not touch hot cable or torch just

by hands.

Fast moving thing may injure you.



Do not put your hands or other things into the

fan shield.



Cover the opened case shell well during cutting

operation.

In case of injury for your skin and eyes, please wear

required guards according to Labor Security and Hygiene
rules. Electrode and nozzle should be replaced only after
the cutter is power off.

Operation should proceed according to related Labor and
Security regulations.

Содержание LGK-40/63IGBT





















Результаты поиска

Содержание LGK-40/63IGBT

Отзывы:

Похожие инструкции для LGK-40/63IGBT

Бренды по названию

Популярные бренды

Hwayuan Electric LGK-40/63IGBT, Руководство оператора

Результаты поиска

Содержание LGK-40/63IGBT

Отзывы:

Похожие инструкции для LGK-40/63IGBT

Бренды по названию

Популярные бренды