Huvitz CFR-3000 Скачать руководство пользователя страница 22

Страница: 22 / 79

Excelon EZ Operator’s Manual

[Connecting the Water Drain Hose] [ Connecting the Water Supply Hose ]

Fixing Clip for Water Drain Hose

•

Fill up 2/3 of the tank with water and make sure that the water supply hose is

not dragged below the pump, and is not folded or interfered with other objects.

•

Use the Clip to tie the Water Supply Hose properly.

NOTE

4.2 Frame Reader & Blocker

①

Remove the shock-absorbing material from the packing box and pull out the

Frame Reader & Blocker carefully.

②

Remove the shock-absorbing material from the workspace of Stylus.

③

Plug the Power Cable into the receptacle at the back of the product and turn on

the power to check the initial operation.

④

If the initial operation works properly, connect Edger and Frame Reader by using

9-pin D-sub Crossed Interface Cable.

Содержание CFR-3000
















































































Результаты поиска

Содержание CFR-3000

Отзывы:

Бренды по названию

Популярные бренды

Huvitz CFR-3000, Руководство оператора

Результаты поиска

Содержание CFR-3000

Отзывы:

Бренды по названию

Популярные бренды