Huvema HU 40 G, Руководство пользователя

Страница: 6 / 28

6
WIJZIGINGEN EN T YPEFOUTEN VOORBEHOUDEN WIJZIGINGEN EN T YPEFOUTEN VOORBEHOUDEN
5.4 o
nderhoud
5.4.1 r
eInIgen
Verwijder al het vet van de machine. Maak alle bewegende delen goed schoon en smeer deze lichtjes.
5.4.2 o
lIe
Afbeelding 3, 4 en 5 – Olie
In de kop van de machine bevindt zich een oliepomp voor het smeren van de tandwielen (afb. 5).
Let op!
De machine wordt geleverd zonder olie!
De machine moet worden gevuld met Shell Tellus 46. Ga als volgt te werk om de machine met olie te vullen
(max. 4.5 liter):
• Verwijder de oliestop bovenop de kop.
• Gebruik een trechter om de olie bij te vullen.
• Stop met olie bijvullen wanneer het niveau de rode lijn op het oliepeilglas bereikt. Het niveau mag nooit boven
de rode lijn uitkomen anders loopt de olie uit de machine. Mocht dit onverhoopt toch een keer gebeuren,
verwijder dan de oliestop aan de linkerkant van de kop en laat de olie weglopen (afb. 4), totdat het niveau zich
op of iets onder de rode lijn bevindt.
5.4.3 s
merIng
Afbeelding 6 – Smering
A As van spindel. Smeer dagelijks de smeernippel naast de afdekking van de spiraalveer.
B Tandwielas van spindelhuls. Smeer dagelijks het oliepunt op de afdekking van de spiraalveer.
Drilling Machine Instruction Book
4
GENERAL DESCRIPTION
1 Driving motor 10 Manual control for gear box
2 Speed selectors 11 Deep stop
3 Speed plate 12 Rapid manual feed control
4 Oil filling opening 13 Oil filling opening
5 Oil pump control sight gage 14 Oil level window
6 Oil level window 15 Oil draining plug
7 Oil draining plug 16 Feed selector
8 Tool ejector 17 Automatic feed lever
9 Spiral spring housing
2 automatic feeds. Mechanical engaging
—
disengaging ,through lever.
FILLING WITH OIL
The speed box incorporates an oil pump to
lubricate the gears.
Attention! The machine is supplied without oil for
transport reasons .Please; follow the following
instructions for filling the machine with oil:
Remove upper plug .Fill oil by using a funnel. Stop
filling oil when oil level reaches the red mark on level
window .This red mark must be never exceeded, as
otherwise, the oil will overflow out the machine.
If this occurs, remove plug and drain oil until oil level
goes down to red mark on level window.
.
Fig 5
Fig 6
Fig 7
Drilling Machine Instruction Book
4
GENERAL DESCRIPTION
1 Driving motor 10 Manual control for gear box
2 Speed selectors 11 Deep stop
3 Speed plate 12 Rapid manual feed control
4 Oil filling opening 13 Oil filling opening
5 Oil pump control sight gage 14 Oil level window
6 Oil level window 15 Oil draining plug
7 Oil draining plug 16 Feed selector
8 Tool ejector 17 Automatic feed lever
9 Spiral spring housing
2 automatic feeds. Mechanical engaging
—
disengaging ,through lever.
FILLING WITH OIL
The speed box incorporates an oil pump to
lubricate the gears.
Attention! The machine is supplied without oil for
transport reasons .Please; follow the following
instructions for filling the machine with oil:
Remove upper plug .Fill oil by using a funnel. Stop
filling oil when oil level reaches the red mark on level
window .This red mark must be never exceeded, as
otherwise, the oil will overflow out the machine.
If this occurs, remove plug and drain oil until oil level
goes down to red mark on level window.
.
Fig 5
Fig 6
Fig 7
Drilling Machine Instruction Book
4
GENERAL DESCRIPTION
1 Driving motor 10 Manual control for gear box
2 Speed selectors 11 Deep stop
3 Speed plate 12 Rapid manual feed control
4 Oil filling opening 13 Oil filling opening
5 Oil pump control sight gage 14 Oil level window
6 Oil level window 15 Oil draining plug
7 Oil draining plug 16 Feed selector
8 Tool ejector 17 Automatic feed lever
9 Spiral spring housing
2 automatic feeds. Mechanical engaging
—
disengaging ,through lever.
FILLING WITH OIL
The speed box incorporates an oil pump to
lubricate the gears.
Attention! The machine is supplied without oil for
transport reasons .Please; follow the following
instructions for filling the machine with oil:
Remove upper plug .Fill oil by using a funnel. Stop
filling oil when oil level reaches the red mark on level
window .This red mark must be never exceeded, as
otherwise, the oil will overflow out the machine.
If this occurs, remove plug and drain oil until oil level
goes down to red mark on level window.
.
Fig 5
Fig 6
Fig 7
Drilling Machine Instruction Book
5
LUBRICATION
Quill Spindle
Daily lubricate with oil the greaser located next the spiral
spring cover .
Quill gearing shaft
Daily lubricate with oil the lubrication port on the spiral
spring cover.
Quill
Clean and lubricate with grease the rack for upward and downward
displacement of quill
—
spindle .
Column
Clean and grease with oil every 50 hours.
Speed box
Fill the box with oil until reaching the indicated level. Change oil
every 2000 hours.
Feed box
Fill the box with oil until reaching the indicated level. Change oil
every 2000 hours.
Rack
Clean and lubricate with grease every 50 hours.
Table
Daily lubricate with oil the two lubrication points.
Fig 8 Fig 9