Huvema HU 30 CROSS-4 Скачать руководство пользователя страница 9

TROUBLE SHOOTING HINTS 

TROUBLE PROBABLE 

CAUSE REMEDY 

Excessive 

Vibration 

1.Motor out of balance

2.Bad motor

1.Balance or replace problem motor.

2.Replace motor

Motor stalls 

1.Over feeding.

2.Dull drill.

3.Motor not building up to

running speed.

4.Bad motor

1.Replace feed rate.

2.Sharpen drill and keep sharp.

3.Replace or repair motor .Check fuses in all

three legs on three phase motors and replace

if necessary.

4.Replace motor

Noisy Operation 

1.Excessive vibration

2.Improper quill adjustment.

3.Nosiy spline.

4.Noisy motor

1.Check remedy under excessive vibration.

2.Adjust quill.

3.Lubricate spline.

4.Check motor bearing or for loose motor fan.

Drill or Tool heats 

Up or burns work 

1.Excessive speed.

2.Chips not clearing.

3.Dull tool.

4.Feed reate too slow.

5.Rotation of drill incorrect.

6.Failure to use cutting oil or

coolant (on steel)

1.Readuce speed.

2.Use pecking operation to clear chips.

3.Sharpen tool or replace.

4.Increase feed enough to clear chips.

5.Reverse motor rotation.

6.Use cutting oil or coolant on steel

Drill leads off 

1.No drill spot.

2.Cutting lips on drill off center.

3.Quill loose in head.

4.Bearing play.

1.Center punch or center drill workpiece.

2.Regrind drill.

3.Tighten quill.

4.Check bearings and reseat or replace if

necessary.

Excessive drill 

Runout or wobble 

1.Bent drill.

2.Bearing play.

3.Drill not seated properly in

chucks.

1.Replace drill.Do not attempt to straighten.

2.Replace or reseat bearings.

3.Loosen , reseat and tighten chuck.

Work or fixture 

Comes loose or 

spins 

1.Failure to clamp workpiece or

work holding device to table.

1.Clamp workpiece or work holding device to

table surface.

Содержание HU 30 CROSS-4























Отзывы: