HUSTLER FasTrak SDX Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 41

HUSTLER FasTrak SDX Скачать руководство пользователя страница 14

REV J

2-8

604856

WARNING: Thrown objects!

•

Always maintain a safe distance from
people and pets when mowing.

•

Always stop machine if someone enters
the area.

•

Inspect area to be mowed for hazards
such as rocks, metal objects and other

debris which may be thrown or entangled

by mower blades. Remove these objects

before mowing.

Part Number 604222

DANGER:

Rotating blades, pulleys & belts

•

Keep shields and covers in place
while machine is in operation.

•

Keep hands, feet and clothing
away from rotating pulleys and

belts.

604222

A.

Fast

B.

Slow

C.

Choke

D.

Mower blade engage/disengage switch

E.

Ignition switch - insert key

F.

OFF

G.

ON

H.

Engine start position

I.

Wear ear protection, eye protection and safety shoes

when operating this equipment.

J.

Read Operator’s Manual before attempting to operate

this machine.

K.

Before starting the engine:

• Read Owner’s Manual
• Disengage mower blades
• Place control levers in park brake position

L.

For maximum electric clutch life engage at 1/2 - 3/4

throttle position.

M.

For maximum electric clutch life disengage at low

throttle position.

604889

Part Number 604889

C

M

D

F

L

B

G

H

E

J

I

A

K

«
...
12
13
14
15
16
...
»

Содержание FasTrak SDX










































Отзывы:

Нет отзывов