manualshive.com logo in svg

HUSTLER FasTrak SDX, Руководство оператора, Страница: 13 / 41

Поделиться
Скачать
HUSTLER FasTrak SDX Скачать руководство пользователя страница 13

604856

2-7

REV J

DANGER:

Battery Hazards! 

Part Number 601815

601815 

•

Do not overfill battery.

•

Electrolyte may overflow and damage 
paint, wiring or structure. When cleaning 

the battery, use soap and water. Be care-

ful not to get soap and water into the 

battery. Use soda mixed in water to 

clean corrosion off the terminals.

•

Always wear eye protection when check-
ing the battery, acid can cause serious 

injury to skin and eyes. If contact occurs, 

flush area with clean water and call phy-

sician immediately. Acid will also dam-

age clothing.

•

Avoid skin con-
tact with battery 

acid

•

Do not allow open flame near the 
battery when charging.

•

Hydrogen gas forms inside the bat-
tery. This gas is both toxic and flam-

mable and may cause an explosion if 

exposed to flame. Always remove 

the negative ground first and replace 

it last.

WARNING:

Fire!

Part Number 601967

•

Clean flammable material from 
machine. Prevent fires by keeping 

engine compartment, top of deck, 

exhaust area, battery, fuel line, fuel 

tank and operator’s station clean of 

accumulated trash, grass clippings, 

and other debris. Always clean up 

spilled fuel and oil.

601967 

WARNING:

Thrown objects!

•

Never operate the mower deck with side 
deflector damaged, altered, removed or in 

raised position, except when the entire 

grass catcher attachment or mulching 

system is being used.

Part Number 604221

DANGER:

Rotating blades, pulleys & belts

•

Keep shields and covers in place 
while machine is in operation

•

Keep hands, feet and clothing 
away from rotating pulleys and 

belts.

604221

Содержание FasTrak SDX










































Отзывы:

Нет отзывов