background image

#OSO-29 #OSO-34 R.1 November 2020

Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces

HARD WIRING INSTALLATION 

19

4.0  HARD WIRING INSTALLATION

4.1  Hard Wiring Connection

WARNING: Turn off the appliance completely and let cool before 

servicing. Only a qualified service person should service and repair this 

electric appliance.
NOTE: A dedicated 15 Amp (or higher) breaker is required.

If it is necessary to hard wire this appliance, a qualified electrician 

must remove the cord connection and wire the appliance directly to 

the household wiring.
This appliance must be electrically connected and grounded in 

accordance with local codes if hard wired. In the absence of local 

codes, use the current ANSI/NFPA 70 'National Electrical Code' in the 

United States or the current CSA C22.1 'Canadian Electrical Code' in 

Canada.

4.1.1  Hard Wiring Installation

Turn off power from circuit breaker before completing any of these 

steps.
The wires are labeled by the yellow clips. 

1.  Remove the cover plate from the bottom of the right side of the 

appliance secured by (3) screws, as shown in Figure 4.1.

2.  Remove the wire connectors from the power cord as shown in 

Figure 4.2. This power cord may be discarded. 

3.  Take the new cover plate supplied in the components packet 

and knock out the 7/8" (22.2mm) hole. 

4.  Install the electrical grommet through the hole in the cover 

plate. Feed wires through the electrical grommet.

5.  Using the wire connectors, connect the green ground wires 

together, and the neutral white and blue wires together, then the 

hot black wires together. See Figure 4.2

6.  Re-install cover plate using (3) screws, as shown in Figure 4.1. 

Cover plate

Figure 4.1, Cover Plate Removal

Figure 4.2, Remove Wire Connectors to Power Cord

Figure 4.3, Wiring through Electrical Grommet and Cover Plate

Electrical grommet

Содержание Kozy Heat Fireplaces OSO-29
































Отзывы: