Husqvarna WH3616 Скачать руководство пользователя страница 46

Страница: 46 / 52

seRVICe JoURnal

action

Date, mtr reading, stamp, sign

Delivery Service

mount caster wheels

Adjust tire pressure of all wheels according to Technical Data

Check that the right amount of oil is in the engine

Adjust the position of the drive levers

Fill with fuel and open the fuel shutoff valve

Start the engine

Check that there is drive to both wheels

Check the mower deck adjustment

Check:

The safety switch for the blade engagement lever

The safety switch for the neutral lock

The safety switches for the OP levers

Parking brake functionality

Driving forward

Driving backward

engaging the blades

Check the idle speed

Inform the customer about:

The need and advantages of following the service schedule

The need and advantages of leaving the machine for service every
300 hours

The effects of service and maintaining a service journal on the
machine’s resale value

Application areas for mulching

Fill in the sales papers, etc.

Certified:

No remaining notes

Delivery service has been carried out

Содержание WH3616





















































Результаты поиска

Содержание WH3616

Отзывы:

Бренды по названию

Популярные бренды

Husqvarna WH3616, Руководство оператора

Результаты поиска

Содержание WH3616

Отзывы:

Бренды по названию

Популярные бренды