Husqvarna WH3616 Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 52

Husqvarna WH3616 Скачать руководство пользователя страница 33

MaIntenanCe

33

WARNING!
Blades are sharp. Protect your hands
with gloves and/or wrap blades with a
heavy cloth when handling.

IMPORTANT INFORMATION
The sharpening of blades should be carried
out by an authorized service workshop.

8062-016

Check the cutting blades

8062-017

Blade attachment

IMPORTANT INFORMATION
Special blade bolt is heat treated. Replace with
a Husqvarna bolt if required. Do not use lower
grade hardware than specified.

Cutting Blades

To achieve the best mowing effect, the blades must
be well sharpened and not damaged.
bent or cracked blades or blades with large nicks
should be replaced.
Damaged blades should be replaced when hitting
obstacles that result in a breakdown. let the service
workshop decide whether the blade can be repaired/
ground or must be replaced.
balance the blades after sharpening.
Check the blade mounts.

Blade replacement

Remove blade bolt by turning counterclockwise.
Install new or resharpened blade with stamped
“GRASS side” facing towards ground/grass (down) or
“THIS SIDe UP” facing deck and cutter housing.
Install and tighten blade bolt securely. Tighten torque
90 ft/lb (122 Nm).

«
...
31
32
33
34
35
...
»

Содержание WH3616





















































Отзывы:

Нет отзывов