manualshive.com logo in svg

Husqvarna WH3616, Руководство оператора

Поделиться
Скачать
Husqvarna WH3616 Скачать руководство пользователя страница 23

opeRatIon

23

8062-044

Operator presence lever - left hand

Running

Depress one operator presence lever and move the 
speed control to the desired speed. Pull the blade 
engagement control upwards. Set the desired rpm 
with the throttle. The best cutting and bagging is 
obtained with engine at top rpm.
While on level terrain, squeeze both drive levers 
slightly. Using thumbs, slide each neutral lock out the 
locked position. Slowly release both drive levers at the 
same time to begin forward motion.
The steering system of this mower uses individual 
right and left drive levers on the handle bars. 
Squeezing either lever will reduce the speed to that 
wheel. With the opposite wheel still under power, a 
turn is accomplished. 
If the drive lever is squeezed even tighter the wheel 
will go into reverse and a tighter more abrupt turn is 
accomplished. Turn left by squeezing the left hand 
lever or turn right by squeezing the right hand lever.

Reverse

The mower moves to the reverse gear when both drive 
levers are pulled fully upward to the handles.

Operating on Hills

Operating on slopes can be hazardous. Read the 

Safety

 section 

Driving on Slopes

.

The slowest speed possible should be used when 

• 

mowing on slopes.
Avoid stopping or changing speed on hills.

• 

make all turns slowly.

• 

WARNING!
Be sure all persons are clear of area 
before engaging the blades.

WARNING!
Never use the machine on terrain that 
slopes more than 10 degrees.
Mow slopes side to side, not up 
and down. Avoid sudden directional 
changes.

Tracking

If the mower is not tracking straight, check the 
air pressure in both rear tires. Recommended 
air pressure is 15 psi (1 bar). Tracking should be 
checked on a flat, level surface.
See 

Tracking Adjustment

 in the 

Controls

 section.

8062-027

Tracking knob

Содержание WH3616





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды