Husqvarna Viking Platinum Q 165 Скачать руководство пользователя страница 14

Страница: 14 / 58

powerquilter 1650 Quilting Machine User’s Guide

| 13

Installation and Setup

Power Cord

To install the power cord

•

Insert the cord into the power connector on the rear of the machine. Secure the cord with the

metal clip. Plug the three-prong end into power source. Do not turn on the machine until the front

handlebars and display are installed.

To disconnect the power cord

•

Unplug the cord from the power outlet. Relese the metal clip where the cord connects with the

machine and then pull out the cord.

For more information, see

Power Switch

in the

Using Your Machine

section of this manual.

NOTE

: Make sure that the machine is off before plugging into power source. The rear power switch

should be in the 0, or off, position.

Carriage

You should have already set up the quilting frame. Refer to the frame manual for detailed instructions

about setting up the frame.

To install the carriage and machine on the frame

1. Place the carriage on the table rails, ensuring that the carriage encoder assembly will be toward the back

of the machine (the power cord side of the machine).

2. Place the machine on the carriage.

CAUTION

: The Platinum Q|165 is heavy. Never attempt to lift it alone. Always use two people when

lifting. Always lift from the throat of the machine, not from the handlebars or needle bar.

3. T he stitch regulation cable is usually already connected to the machine encoder. The connector in the

middle of the stitch regulation cable, plugs into the machine encoder. The two cables are secured with

clips on the machine which helps manage them.

4. The remaining length of cable with a connector on the very end plugs into the carriage encoder.

IMPORTANT

: Make sure the keyed portion of the cable connector aligns with the keyed portion of

the encoder connector. Do not force.

IMPORTANT

: If the machine is to be removed from the carriage, the cable must first be

disconnected from the carriage encoder assembly. The other two connectors on the cable should

remain in place. Failure to unplug the cable when removing the machine from the carriage could

result in damage to the cable, encoders, and carriage.

Содержание Viking Platinum Q 165


























































Результаты поиска

Содержание Viking Platinum Q 165

Отзывы:

Похожие инструкции для Viking Platinum Q 165

Бренды по названию

Популярные бренды

Husqvarna Viking Platinum Q 165, Руководство пользователя

Результаты поиска

Содержание Viking Platinum Q 165

Отзывы:

Похожие инструкции для Viking Platinum Q 165

Бренды по названию

Популярные бренды