Husqvarna TS 250 XS Скачать руководство пользователя страница 9

Страница: 9 / 20

Specifications

MODEL NO.

TS 250 XS

TYPE

1-1/2 HP, 115/208-230/

2 HP, 115/230V-60Hz

Blade Guard

Capacity

10"

(250 mm)

Blade Shaft RPM:

3880

Max. Depth of Cut:

3-3/4” (95 mm)

Maximum Material

Size:

Up to 24” wide x 36” long (610 x 914 mm)

Blade Arbor Size:

5/8” (15.9 mm)

Blade Shaft:

Sealed Ball Bearings

Blade Shaft Drive:

3VX V-Belt (2 Band)

Blade Coolant:

Water

Water Pan:

Powder coat finish to resist chipping. Sliding tray accommodates materials from 4” to 24”

(102 to 610mm); with spring tensioned latches.

Water Pan Capacity:

27-1/2 gallons (105 liters)

Cutting Table:

Formed steel, powder coated, high density polyethylene top, extended rails for longer cuts

and two intermediate supports for stability and consistent tracking. Small cutting cart for

smaller tiles features “Sure-grip” bonded surface and rides on separate rails: 24” x 36” (610

x 914mm). Table extension: 12” x 24” (305 x 620mm)

Water Pump:

115V, 60 Hz., 1-phase, 0.5 amps, 300 gal/hr. (1144 l /hr.) Output

Totally Epoxy Sealed, Thermal Over Load Protected,

lifetime lubricant

Cutting Head:

Cast aluminum pivoting head, can be preset, locked or fully adjusted to varying heights.

Weight Pounds (kg):
Saw Crated:

410 (186)

452 (205)

Saw Uncrated:

360 (164)

383 (174)

Power Source

TYPE:

Electric

Engine / Motor:

Baldor

Horsepower (kw):

1-1/2 (1.1)

2 (1.5)

RPM:

3450

Specifications:

T.E.F.C.

Voltage:

115 / 208-230

Cycle (Hz) /

Current / Phase:

60 * / A.C. / 1

Starter:

Capacitor

Full Load Amperage:

17.2 / 9-8.6

16.8 / 7.6-8.4

Coolant:

Air

Содержание TS 250 XS





















Результаты поиска

Содержание TS 250 XS

Отзывы:

Husqvarna TS 250 XS, Руководство оператора, Страница: 9 / 20

Результаты поиска

Содержание TS 250 XS

Отзывы: