Husqvarna TS 250 XS Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 20

Husqvarna TS 250 XS Скачать руководство пользователя страница 5

5

• Motor Off

• Parar El Motor

• Use In Well Ventilated Area

• Usar En Una Área Bien Ventilada

• Do Not Use In Flammable Areas

• No Usar In Áreas Inflamables

• Machinery Hazard, Keep Hands And Feet Clear.

• Máquina Peligrosa - Mantenga Manos Y Pies Alejados De La Máquina

• No Non-working Personnel In Area

• Prohibido Para Personas Ajenas A La Obra

• No Smoking

• No Fumar

• Do Not Operate Without All Guards In Place

• No Operar Sin Todas Las Protecciones In Su Sitio

• Always Keep the Blade Guards In Place

• Mantenga Siempre Las Protecciones De La Hoja En Su Sitio

• Keep Work Area Clean/Well Lit, Remove All Safety Hazards

• Mantenga Limpio El Sitio De Trabajo/Bien Iluminado, Elimine Todos Los Riesgos De Seguridad

• Dangerously High Noise Level

• Nivel De Ruido Elevadamente Peligroso

• Pay Extreme Attention To The Care And Protection Of The Machine Before Starting Up

• Ponga Extrema Atención Al Cuidado Y Preparación De La Máquina Antes De Ponerla En Marcha

• Remove Tools From Area and Machine

• Elimine Las Herramientas Del Área Y De La Máquina

• Electrical Switch - OFF

• Conmutador De Apagado Eléctrico

• Electrical Switch - ON

• Conmutador De Encendido Eléctrico

• Electrical Switch - Start

• Conmutador De Arranque Eléctrico

«
...
3
4
5
6
7
...
»

Содержание TS 250 XS





















Отзывы:

Нет отзывов