Husqvarna FE 450 Скачать руководство пользователя страница 54

Страница: 54 / 128

12 SERVICE WORK ON THE CHASSIS

12.15

Installing the front fender

F00283-10

Main work

–

Position the front fender. Mount and tighten screws



Guideline

Remaining screws, chassis

10 Nm (7.4 lbf ft)

–

Mount and tighten screws



Guideline

Remaining screws, chassis

10 Nm (7.4 lbf ft)

Finishing work

–

Install the headlight mask with the headlight. (

p. 90)

–

Check the headlight setting. (

p. 91)

12.16

Removing the shock absorber

Preparatory work

–

Raise the motorcycle with a lift stand. (

p. 45)

K00589-10

Main work

–

Remove the cable ties.

–

Remove screws



–

Remove screws



with the washers.

–

Remove the frame protectors on the left and right.

F00284-10

–

Remove screw



–

Remove fitting



Info

Raise the wheel slightly to be able to remove the screws more easily.

F00285-10

–

Press angle lever



toward the rear.

–

Press linkage lever



downward.

Содержание FE 450

































































































































Результаты поиска

Содержание FE 450

Отзывы:

Похожие инструкции для FE 450

Бренды по названию

Популярные бренды

Husqvarna FE 450, Руководство пользователя

Результаты поиска

Содержание FE 450

Отзывы:

Похожие инструкции для FE 450

Бренды по названию

Популярные бренды