Husqvarna FE 450 Скачать руководство пользователя страница 92

Страница: 92 / 128

15 ELECTRICAL SYSTEM

15.7

Installing the headlight mask with the headlight

F00340-11

Main work

–

Connect plug-in connectors



F00341-10

–

Position the headlight mask and secure it with rubber bands



The holding lugs engage in the fender.

F00342-10

–

Position brake line



and wiring harness



in the brake line guide.

Finishing work

–

Check the headlight setting. (

p. 91)

15.8

Changing the headlight bulb

Note

Damage to reflector

Reduced brightness.

–

Grease on the lamp will evaporate due to the heat and be deposited on the reflector. Clean the lamp and keep it free of grease

before mounting.

Preparatory work

–

Switch off all power consumers and switch off the engine.

–

Remove the headlight mask with the headlight. (

p. 89)

F00343-10

Main work

–

Turn protection cap



together with the underlying bulb socket counterclock-

wise all the way and remove it.

–

Pull bulb socket



of the parking light out of the reflector.

Содержание FE 450

































































































































Результаты поиска

Содержание FE 450

Отзывы:

Похожие инструкции для FE 450

Бренды по названию

Популярные бренды

Husqvarna FE 450, Руководство пользователя

Результаты поиска

Содержание FE 450

Отзывы:

Похожие инструкции для FE 450

Бренды по названию

Популярные бренды