Husqvarna F2303U7 Скачать руководство пользователя

Страница: 81 / 171

SERVICE WORK ON THE CHASSIS 12

H03708-10

Main work

–

Loosen nut

–

Loosen nuts

–

Adjust the chain tension by turning adjusting screws

left

and right.
Guideline

Chain tension

55 … 58 mm (2.17 …
2.28 in)

Turn adjusting screws

on the left and right so that the

markings on the left and right chain adjusters are in the
same position relative to reference marks

. The rear

wheel is then correctly aligned.

–

Tighten nuts

–

Make sure that chain adjusters

are fitted correctly on

adjusting screws

–

Tighten nut

Guideline

Nut, rear wheel spin-
dle

M20x1.5

80 Nm (59 lbf ft)

Info

The wide adjustment range of the chain adjusters
(32 mm (1.26 in)) enables different secondary ratios
with the same chain length.
Chain adjusters

can be turned by 180°.

Finishing work

–

Remove the motorcycle from the lift stand. (

p. 56)

12.36

Checking the chain, rear sprocket, engine sprocket, and chain guide

Preparatory work

–

Raise the motorcycle with a lift stand. (

p. 56)

400227-01

Main work

–

Shift the transmission into neutral.

–

Check the chain, rear sprocket, and engine sprocket for
wear.
» If the chain, rear sprocket or engine sprocket is worn:

–

Change the drivetrain kit.

Info

The engine sprocket, rear sprocket, and chain
should always be replaced together.

Содержание F2303U7












































































































































































Результаты поиска

Содержание F2303U7

Отзывы:

Похожие инструкции для F2303U7

Бренды по названию

Популярные бренды

Husqvarna F2303U7, Руководство пользователя

Результаты поиска

Содержание F2303U7

Отзывы:

Похожие инструкции для F2303U7

Бренды по названию

Популярные бренды