Husqvarna F2303U7 Скачать руководство пользователя

Страница: 58 / 171

12 SERVICE WORK ON THE CHASSIS

12.1

Raising the motorcycle with a lift stand

401942-01

Note

Danger of damage

The parked vehicle can roll away or fall

over.

–

Park the vehicle on a firm and level surface.

–

Raise the motorcycle at the frame underneath the engine.

Lift stand (81329955100)

Neither wheel is in contact with the ground.

–

Secure the motorcycle against falling over.

12.2

Removing the motorcycle from the lift stand

Note

Danger of damage

The parked vehicle can roll away or fall over.

–

Park the vehicle on a firm and level surface.

401943-10

–

Remove the motorcycle from the lift stand.

–

Remove the lift stand.

–

To park the motorcycle, press side stand

to the ground

with your foot and lean the motorcycle on it.

Info

When you are riding, the side stand must be folded up
and secured with the rubber strap.

12.3

Bleeding the fork legs

Preparatory work

–

Raise the motorcycle with a lift stand. (

p. 56)

402556-10

Main work

–

Release bleeder screws

Any excess pressure escapes from the interior of the
fork.

–

Tighten the bleeder screws.

Finishing work

–

Remove the motorcycle from the lift stand. (

p. 56)

Содержание F2303U7












































































































































































Результаты поиска

Содержание F2303U7

Отзывы:

Похожие инструкции для F2303U7

Бренды по названию

Популярные бренды

Husqvarna F2303U7, Руководство пользователя

Результаты поиска

Содержание F2303U7

Отзывы:

Похожие инструкции для F2303U7

Бренды по названию

Популярные бренды