Husqvarna F2303U7 Скачать руководство пользователя | Manualshive

Страница: 86 / 171

background image

12 SERVICE WORK ON THE CHASSIS

84

12.41

Adjusting the basic position of the clutch lever

H03648-11

–

Adjust the basic position of the clutch lever to your hand size
by turning adjusting screw

1

.

Info

When the adjusting screw is turned counterclockwise,
the clutch lever moves away from the handlebar.
When the adjusting screw is turned clockwise, the
clutch lever moves closer to the handlebar.
The range of adjustment is limited.
Turn the adjusting screw by hand only, and do not
apply any force.
Do not make any adjustments while riding.

12.42

Checking/correcting the fluid level of the hydraulic clutch

Warning

Skin irritation

Brake fluid causes skin irritation.

–

Keep brake fluid out of the reach of children.

–

Wear suitable protective clothing and safety glasses.

–

Do not allow brake fluid to come into contact with the skin, the eyes or clothing.

–

Consult a doctor immediately if brake fluid has been swallowed.

–

Rinse the affected area with plenty of water in the event of contact with the skin.

–

Rinse eyes thoroughly with water immediately and consult a doctor if brake fluid comes into contact
with the eyes.

–

If brake fluid spills on to your clothing, change the clothing.

Note

Environmental hazard

Hazardous substances cause environmental damage.

–

Dispose of oils, grease, filters, fuel, cleaning agents, brake fluid, etc., correctly and in compliance
with the applicable regulations.

Info

The fluid level rises with increasing wear of the clutch facing discs.
Never use DOT 5 brake fluid. It is silicone-based and purple in color. Oil seals and clutch lines are not
designed for DOT 5 brake fluid.
Avoid contact between brake fluid and painted parts. Brake fluid attacks paint.
Only use clean brake fluid from a sealed container.

H03713-10

–

Move the clutch fluid reservoir mounted on the handlebar to a
horizontal position.

–

Remove screws

1

.

–

Take off cover

2

with membrane

3

.

–

Check the fluid level.

Fluid level below container
rim

4 mm (0.16 in)

» If the level of the fluid does not meet specifications:

–

Correct the fluid level of the hydraulic clutch.

«
...
84
85
86
87
88
...
»

Содержание F2303U7












































































































































































Отзывы:

Нет отзывов

Похожие инструкции для F2303U7

Бренд: Honda Страницы: 118

Бренд: hepco & becker Страницы: 6

Бренд: DUCATI Performance Страницы: 5

Бренд: Honda Страницы: 91

Бренд: Suzuki Страницы: 447

990D0-44G00-ALM

Бренд: Suzuki Страницы: 24

Бренд: Sundstrom Страницы: 68

MSS X9 EVOLUTION 250

Бренд: PIAGGIO Страницы: 262

MP3 500 ie SPORT Business LT 2011

Бренд: PIAGGIO Страницы: 375

Бренд: IBEX Страницы: 2

SENDA R/SM 125 4T Baja

Бренд: Derbi Страницы: 124

Бренд: Cagiva Страницы: 407

Бренд: HYOSUNG Страницы: 90

Бренд: ZONGSHEN Страницы: 76

BASE SATIN 55-85-010

Бренд: Thunderbike Страницы: 8

390 Duke AR 2019

Бренд: KTM Страницы: 257

Бренд: HealTech Electronics Страницы: 2

Бренд: HealTech Electronics Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды