Husqvarna F2303U7 Скачать руководство пользователя

Страница: 26 / 171

6 CONTROLS

6.24

Side stand

401943-10

The side stand

is located on the left of the vehicle.

401944-10

The side stand is used for parking the motorcycle.

Info

When you are riding, side stand

must be folded up

and secured with rubber strap

6.25

Steering lock (All EU models)

H03662-10

Steering lock

is fitted on the left side of the steering head.

The steering lock is used to lock the steering. Steering, and
therefore riding, is no longer possible.

6.26

Locking the steering (All EU models)

Note

Danger of damage

The parked vehicle can roll away or fall over.

–

Park the vehicle on a firm and level surface.

400732-01

–

Park the vehicle.

–

Turn handlebar as far as possible to the right.

–

Insert the key for the steering lock into the steering lock, turn
it to the left, press it in, and turn it to the right. Pull out the
key for the steering lock.

Steering is no longer possible.

Info

Never leave the key for the steering lock in the steer-
ing lock.

Содержание F2303U7












































































































































































Результаты поиска

Содержание F2303U7

Отзывы:

Похожие инструкции для F2303U7

Бренды по названию

Популярные бренды

Husqvarna F2303U7, Руководство пользователя

Результаты поиска

Содержание F2303U7

Отзывы:

Похожие инструкции для F2303U7

Бренды по названию

Популярные бренды